International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Tire Kickin' > General FSJ Tech

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 05-31-2009, 02:53 PM
rambling_rebel rambling_rebel is offline
232 I6
 
Join Date: Jul 03, 2004
Location: Ontario
Posts: 36
direction

here goes again (I hit a wrong key and lost my post)

I know its been talked about in many posts here, but I have a specific question about I6-v8 conversion.

vehicle = '82 j10 Honcho, short box stepside
engine 360

I know about the tranny moving forward and longer driveshafts (I have a set out of a j20)

I know about the wiring harness and exhaust (both are going in new)

question is about the engine mount "horns", my I6 honcho has the horns welded on the frame, as did the '85 GW I just parted and scrapped

I went to my home town and theres a '76 j10 shortbox quietly becoming a rust turd (not there yet, but will be soon) and the front clip is off and its v8 horns are bolted on

questions

1 - why the mix of Bolted vs welded

2 - are these bolted on "horns" relatively easy to find?

and an opinion

I have NOS front and rear bumpers, I am in the middle of a colour change to "Hunter Green", I was thinking about colour-keying the bumpers and rollbar to match the hunter green (currently front is chrome and back is white both with factory stickers still on them )

the vehicle is

360 with decent healthy cam +offenhauser 2x4 with twin carter 525carbs
3" suspension lift
M/T rims and goodyear ATS 33"
Gladiator front grill setup
auto with stock conv. (for now)
front dana 44 rear amc20 (ratios unknown)
GW leather power interior

intended use = tooling around town, towing AMX to drags, the odd trip down the 1/4 mile and maybe the dd 4x4g with daughter and her tj

thanks
RR

ps. anyone know a source for class 5 trailer hitches for FSJ's?
Reply With Quote
  #2  
Old 05-31-2009, 10:38 PM
jaber's Avatar
jaber jaber is offline
Dragin Az
 
Join Date: Oct 17, 2003
Location: Chino Valley, Arizona
Posts: 8,076
I honestly dont have an answer on the mount thing. I'm doing the opposite so if you dont have plans for the I-6 horns, I'd be interested in them.

I would also be interested in seeing pics. If you dont already, get a Photobucket acct and it'll let you post them in your threads. theres a good sticky at the top of the general discussion page. Sounds like a nice ride. One day I hope to have a Javelin or AMX to pull behind mine. I have a friend here that has a 9 second AMX, I love seeing it and would like to see yours as well.
__________________
Jeff


46 cj2a

51 Willys p/u
'51 Willys Parkway Conversion
'74 CJ5
'75 J-20 Wrecker
'75 J-20 Cummins service bed
'77 J-10 p/u
'79 Cherokee
'88 Grand Wagoneer
http://s252.photobucket.com/albums/hh14/jeffaber/
Reply With Quote
  #3  
Old 06-01-2009, 06:04 AM
rambling_rebel rambling_rebel is offline
232 I6
 
Join Date: Jul 03, 2004
Location: Ontario
Posts: 36
Direction

Thanks for the reply Jaber, sure, I'll have no use for the i6 "horns, heck I have no use for the engine that came out of it, I only run v8's. and this is some funky rare serpentine i6 they apparantly had in '82 to boot.

I'll post pics shortly, one of my daughters messed up my digital cam, probably dropped it in the mud when she went mudding

as for my AMX, it was the hunter green g pak car featured on Dream Car garage's 7-car musclecar shootout a few years back on speed....

it's been approx. 35deg F up here the last few days with thunderstorms (the truck is out in the driveway so doing the lift would be easier, stoopid me, junk sits inside and all my nice stuff sits outside)
Reply With Quote
  #4  
Old 06-01-2009, 07:57 AM
tgreese's Avatar
tgreese tgreese is offline
 
Join Date: May 29, 2003
Location: Medford MA USA
Posts: 11,441
All the mounts I've seen have been bolted and welded. Some may be riveted and welded. I think that if you look closely at the J-truck that there will be a bead of weld along with the bolts. That is, unless the mounts are from somebody's previous swap-in.
__________________
Tim Reese
Maine beekeeper's truck: '77 J10 LWB, 258/T15/D20/3.54 bone stock, low options (delete radio), PS, hubcaps.
Browless and proud: '82 J20 360/T18/NP208/3.73, Destination ATs, 7600 GVWR
Copper Polly: '75 CJ-6, 304/T15, PS, BFG KM2s, soft top
GTI without the badges: '95 VW Golf Sport 2000cc 2D
ECO Green: '15 FCA Jeep Cherokee KL Trailhawk
Reply With Quote
  #5  
Old 06-01-2009, 11:46 AM
rambling_rebel rambling_rebel is offline
232 I6
 
Join Date: Jul 03, 2004
Location: Ontario
Posts: 36
thanks tgreese, I'll go double-check today or tomorrow, with the fleet-side shortbox, I just saw the bolts and thought "hhmm, bolted on" I didn't think to check for welds, and on my stepside I just saw welds and thought "****, now I have to remember how to stick-weld" and never looked further

RR
Reply With Quote
  #6  
Old 06-01-2009, 01:38 PM
rambling_rebel rambling_rebel is offline
232 I6
 
Join Date: Jul 03, 2004
Location: Ontario
Posts: 36
I just checked the stepside, you are correct, they seem to be bolted to the side of the frame by two bolts and welded across the top of the frame, I'll check the fleetside tomorrow.

are decent v8 ones easy to come across?
Reply With Quote
  #7  
Old 06-01-2009, 05:15 PM
jaber's Avatar
jaber jaber is offline
Dragin Az
 
Join Date: Oct 17, 2003
Location: Chino Valley, Arizona
Posts: 8,076
If you cant find a decent set let me know and I'll cut a set off for you.
__________________
Jeff


46 cj2a

51 Willys p/u
'51 Willys Parkway Conversion
'74 CJ5
'75 J-20 Wrecker
'75 J-20 Cummins service bed
'77 J-10 p/u
'79 Cherokee
'88 Grand Wagoneer
http://s252.photobucket.com/albums/hh14/jeffaber/
Reply With Quote
  #8  
Old 06-02-2009, 07:31 PM
rambling_rebel rambling_rebel is offline
232 I6
 
Join Date: Jul 03, 2004
Location: Ontario
Posts: 36
thanks for the offer, I will be measuring up the stepside tomorrow and taking pics, and then I will be at the fleetside on Friday and will do the same there.

I'm more an AMC guy than a jeep guy, but you wouldn't know it by looking in my shop or driveway. 5 jeeps + 4 amc's and my best pal of 35 years owns the local AMC (dodge)/ Jeep dealership and its been in his family since 1945, he just doesn't remember a whole lot about the FSJ stuff.....

thanks you guys for your assist

Randy
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 03:31 AM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2021, Jelsoft Enterprises Ltd.
corner corner