International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Tire Kickin' > General FSJ Discussion

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 09-01-2010, 04:15 PM
will e's Avatar
will e will e is offline
Always Broke
 
Join Date: Nov 16, 2001
Location: Mesa AZ
Posts: 9,994
jeep is dead. Anyone know the part number for ignition module in Z&M HEI unit?

see below
__________________
82 Cherokee WT – SFwith Alcan/agr box/Borgeson shaft/ 401/performer/Holley TA/HEI/BeCool/727/ALTAS(2.0/2.72/5.44)/D60 Snofighter(Yukon Zip,hubs,stubs,4.56)/14 Bolt (FF,BF shave,Discs, ARB,Artec Truss)/MTR 37/Corbeau Moab Seats /Hella/tuffy console/sliders/custombumpers&roll bar/WARN 8000/steering brace/CO2 Tank/dual batts/custom TCskid plate






Last edited by will e : 09-01-2010 at 06:20 PM.
Reply With Quote
  #2  
Old 09-01-2010, 04:15 PM
will e's Avatar
will e will e is offline
Always Broke
 
Join Date: Nov 16, 2001
Location: Mesa AZ
Posts: 9,994
jeep is dead. Anyone know the part number for ignition module in Z&M HEI unit?

I got a HEI a few years back. It died. I suspect it is the ignition module. The guys at the parts store don’t know how to look it up without a part number or vehicle type. Anyone know what he uses as a basis for this or a part number? I just left him a voice mail and email but jeep is dead so fastest answer I can get will help.

ANd Ralph, you were right. again.
__________________
82 Cherokee WT – SFwith Alcan/agr box/Borgeson shaft/ 401/performer/Holley TA/HEI/BeCool/727/ALTAS(2.0/2.72/5.44)/D60 Snofighter(Yukon Zip,hubs,stubs,4.56)/14 Bolt (FF,BF shave,Discs, ARB,Artec Truss)/MTR 37/Corbeau Moab Seats /Hella/tuffy console/sliders/custombumpers&roll bar/WARN 8000/steering brace/CO2 Tank/dual batts/custom TCskid plate





Reply With Quote
  #3  
Old 09-01-2010, 04:46 PM
The Colonel's Avatar
The Colonel The Colonel is offline
FSJ Maniac
 
Join Date: Feb 21, 2010
Location: Chicagoland
Posts: 2,842
It's got the 4-pin module correct?

Standard part number LX301
AC Delco D1906

Have them look it up for a 74 Impala 5.7L
__________________

Reply With Quote
  #4  
Old 09-01-2010, 04:51 PM
fulsizjeep's Avatar
fulsizjeep fulsizjeep is offline
Señor Jackhead
 
Join Date: Aug 21, 2002
Location: Jubilee Jeeps.SWCO
Posts: 22,261
Is yours a Mallory brand? Just curious...

The spare I bought with Ralph last November was at an Autozone near his place. There were bunches of brands to chose from with prices to match. I am pretty sure what I got was a Borg Warner part but will check when I get home.
__________________
Flint
Ran when parked.
http://jubileejeeps.org/quadratrac
88 GW, 401/727/208, 5" lift, D44s/4.10s/locked up, 35s and a few Evil Twin mods, http://eviltwinfab.com and a few TT's Fabworks mods, http://www.ttsfabworks.com
76 401 Wag, 77 401 Wag, 77 401 J20
Reply With Quote
  #5  
Old 09-01-2010, 05:17 PM
joe joe is offline
 
Join Date: Apr 28, 2000
Location: PNWet, USA
Posts: 22,339
Have ya tried calling Zack?
__________________
joe
"Don't mind me. I'm just here for the alibi"
Reply With Quote
  #6  
Old 09-01-2010, 05:41 PM
tazzerzz's Avatar
tazzerzz tazzerzz is offline
Gear Head
 
Join Date: Jan 31, 2007
Location: Flagstaff, AZ
Posts: 685
Quote:
Originally Posted by will e
[FONT='Calibri','sans-serif']I got a HEI a few years back. It died. I suspect it is the ignition module. The guys at the parts store don’t know how to look it up without a part number or vehicle type. Anyone know what he uses as a basis for this or a part number? I just left him a voice mail and email but jeep is dead so fastest answer I can get will help.[/font]
[FONT='Calibri','sans-serif'][/font]
[FONT='Calibri','sans-serif'][/font]
what motor are you running as I have a new ecm and a new unused dura spark pick-up if you need em cheap
weather pac connectors on the pick-up \\
I went HEI and never installed the pick-up
The ecm is about three months old, I also have a good used one
20.00 for all plus the trip

If you want a good HEI go to ebay search for 360 or 258 HEI
only buy the skip white dist as all of the others are Chinese junk
You can get a good one for about 56.00
__________________
1980 j10 w/Brow and a nice fresh dent on the bed
Reply With Quote
  #7  
Old 09-01-2010, 05:41 PM
grand_wag_85's Avatar
grand_wag_85 grand_wag_85 is offline
Murphy's Law Poster Child
 
Join Date: Dec 03, 2003
Posts: 10,707
1978 Chevy with a 350. HEI was still in use up to '84 but without vacuum advance.
__________________
You know it's bad when your car's on the EPA's 10 most wanted list!

'82 J10
'65 J2000

Reply With Quote
  #8  
Old 09-01-2010, 08:29 PM
will e's Avatar
will e will e is offline
Always Broke
 
Join Date: Nov 16, 2001
Location: Mesa AZ
Posts: 9,994
thanks! You were correct. I got an email from Zack (Z&M) and he said 1979 chevy truck.

Autozone part number DR100. Worked like a charm. Only $21.99. I am going to buy an extra tomorrow and toss it in the 'off road' tool box.
__________________
82 Cherokee WT – SFwith Alcan/agr box/Borgeson shaft/ 401/performer/Holley TA/HEI/BeCool/727/ALTAS(2.0/2.72/5.44)/D60 Snofighter(Yukon Zip,hubs,stubs,4.56)/14 Bolt (FF,BF shave,Discs, ARB,Artec Truss)/MTR 37/Corbeau Moab Seats /Hella/tuffy console/sliders/custombumpers&roll bar/WARN 8000/steering brace/CO2 Tank/dual batts/custom TCskid plate





Reply With Quote
  #9  
Old 09-01-2010, 09:19 PM
FSJ Guy FSJ Guy is offline
 
Join Date: Mar 20, 2005
Location: Colorado
Posts: 10,062
Quote:
Originally Posted by will e
thanks! You were correct. I got an email from Zack (Z&M) and he said 1979 chevy truck.

Autozone part number DR100. Worked like a charm. Only $21.99. I am going to buy an extra tomorrow and toss it in the 'off road' tool box.

Don't forget the heatsink grease! Without it, you'll be installing your spare module really soon!
__________________
Ethan Brady
1987 Grand Wagoneer, slightly longer than stock.

www.bigscaryjeep.com

Don't mess with me. I once killed a living hinge.
Reply With Quote
  #10  
Old 09-01-2010, 09:54 PM
will e's Avatar
will e will e is offline
Always Broke
 
Join Date: Nov 16, 2001
Location: Mesa AZ
Posts: 9,994
Quote:
Originally Posted by FSJ Guy
Don't forget the heatsink grease! Without it, you'll be installing your spare module really soon!

It was included with the part. Reminds me of when I used to put PC's together and had to add the stuff on the CPU's....
__________________
82 Cherokee WT – SFwith Alcan/agr box/Borgeson shaft/ 401/performer/Holley TA/HEI/BeCool/727/ALTAS(2.0/2.72/5.44)/D60 Snofighter(Yukon Zip,hubs,stubs,4.56)/14 Bolt (FF,BF shave,Discs, ARB,Artec Truss)/MTR 37/Corbeau Moab Seats /Hella/tuffy console/sliders/custombumpers&roll bar/WARN 8000/steering brace/CO2 Tank/dual batts/custom TCskid plate





Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
TFI!!! HELP!!!!!!!!(Update!!) Its all about the Jeep General FSJ Tech 29 04-05-2011 03:39 PM
Simple SOA part number Blake Off-Road FSJ Tech 2 01-02-2008 09:23 AM
Where should my tranny get worked on? jgarcia2 General FSJ Tech 10 03-25-2004 06:36 PM
AMC/Jeep Manual Transmission Info James 007 General FSJ Tech 0 09-02-2002 07:40 AM
OHM rating for 1981 Jeep J10 360 2bbl fuel tank sending unit to guage badaboom General FSJ Tech 11 06-20-2002 04:47 PM


All times are GMT -6. The time now is 02:18 PM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
corner corner