Tweet
I need one rear axle shaft for the " centered Dana 60 " vs. the offset unit. The axle shaft I need is about 36inches long from the spline end to the inner flange lip
-
1985 J-20 401 6 inch lift, 37's plow truck. CURRENT PROJECT
1986 CJ 7 360 T-18 granny low Dana 44 , 4 inch lift 35's
1882 CJ 7 360 727 auto Dana 60's 35's cage
1970 AMX was SCCA B production. 390 cross ram. GOOGLE IT -
How many splines does the axle need to have?Jeep "because mother nature hates flat roads to"
http://www.ifsja.org/forums/vb/showthread.php?t=180974
99' Dodge ram 2500 4x4 crew cab 5.9 Cummins ,backup work truck for now
73' Jeep J4000 (named Heep or Desert Dragon) amc 360 V8 converted to LPG with T15/D20 (was my daily work truck for thirteen years and is getting major overhaul at the moment!)
80' Jeep cj5 350 V8 Chevy/sm420/D300 project
70/71 Jeep J4000 parts truck with Buick 350
Former vehicles:
85' Volkswagen caddy mk1 1.6 diesel.
83 Toyota land cruiser BJ42 3.4 diesel. -
SPLINE COUNT
30 spline1985 J-20 401 6 inch lift, 37's plow truck. CURRENT PROJECT
1986 CJ 7 360 T-18 granny low Dana 44 , 4 inch lift 35's
1882 CJ 7 360 727 auto Dana 60's 35's cage
1970 AMX was SCCA B production. 390 cross ram. GOOGLE ITComment
-
Don't know how accurate measurements are , but maybe this could be a solution!?Jeep "because mother nature hates flat roads to"
http://www.ifsja.org/forums/vb/showthread.php?t=180974
99' Dodge ram 2500 4x4 crew cab 5.9 Cummins ,backup work truck for now
73' Jeep J4000 (named Heep or Desert Dragon) amc 360 V8 converted to LPG with T15/D20 (was my daily work truck for thirteen years and is getting major overhaul at the moment!)
80' Jeep cj5 350 V8 Chevy/sm420/D300 project
70/71 Jeep J4000 parts truck with Buick 350
Former vehicles:
85' Volkswagen caddy mk1 1.6 diesel.
83 Toyota land cruiser BJ42 3.4 diesel.Comment
-
AXLE
I THINK THIS COULD WORK!!!!1985 J-20 401 6 inch lift, 37's plow truck. CURRENT PROJECT
1986 CJ 7 360 T-18 granny low Dana 44 , 4 inch lift 35's
1882 CJ 7 360 727 auto Dana 60's 35's cage
1970 AMX was SCCA B production. 390 cross ram. GOOGLE ITComment
-
The flange that bolts to the hub on our J-20s is much smaller in diameter and bolt-pattern than most other D60 full-float rear axles, including the Dodge axles, so even if the shaft was the same length and splines, it might not bolt to the hub.Originally posted by JERSEY JOE
Our axle uses the same flange-size as the D60s used on Chevy trucks up through '72, when they were replaced by GM's own 14-bolt axle. You'd have better luck finding a compatible axle shaft from one of those applications, but to be honest, another J-20 axle will be your best bet.1987 J-20
Video projects for my J-20 on YoutubeComment
-
AXLE SHAFT
I agree that a Jeep axle would be the best but have not despite my best efforts found one. I still have time since the project is not yet rolling but looks like I will have to send my sample axle out to have one made.1985 J-20 401 6 inch lift, 37's plow truck. CURRENT PROJECT
1986 CJ 7 360 T-18 granny low Dana 44 , 4 inch lift 35's
1882 CJ 7 360 727 auto Dana 60's 35's cage
1970 AMX was SCCA B production. 390 cross ram. GOOGLE ITComment
Comment