International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Tire Kickin' > General FSJ Discussion

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 04-08-2019, 10:51 PM
ZackN920's Avatar
ZackN920 ZackN920 is offline
350 Buick
 
Join Date: Nov 18, 2015
Location: Stephenson County, IL
Posts: 844
Can I just weld my air injection tubes shut?

Hey guy's, been awhile... and been busy.

Along with all the normal spring preparation stuff, I've been cleaning up /out my (out of town) garage and all my grounds-keeping equipment. The building was flooded. Had 13" of water in it. All my small engine equipment was under water and just coated with mud/muck/oil and what ever else that was in the water. Not too happy as I've been cleaning/working constantly with it for the last 2 weeks. Cleaning the building and restoring my junk back to running, useable shape.


Well, on to the topic of this thread:

I've apparently always had a SMALL exhaust leak under the hood that I've never really bothered all that much with. It's not really noticeable (while driving) unless the wing-window is open. If that's open, and everything else is shut, it comes in and is easily noticed. Originally, I thought it was mostly from under the vehicle. The Y pipe to exhaust pipe has always been just, sort of a loose connection. It was tight together (held with a traditional exhaust clamp) but when under the vehicle I could see the tell tale soot marks you get with leaks.
That recently came apart again (slipped out) and since I have a welder now, I decided to just weld it. Got it all welded, sealed up (can't feel a leak with it running and my hands on the pipe), but-hmm still have that smell.

Looking more at my air injection tube set up(which is completely useless for me) I found a hole under the valve on the driver side that the old air tube would connect to. This morning while cold I put my hand over it with the engine idling and sure enough, pretty strong little breeze coming out of it. I can only imagine how much comes out during normal driving or even, full throttle shots.

Most of you that know me here, know that I have (well, started with) a total rusty POS. I'm sure the injection bolts WONT come out. So don't even tell me-"just unbolt it and put regular bolts in". That's not happening with this Jeep. and no, I don't want, or plan to pull the manifolds.
So, Can I just cut the tubes flush where they come out of the exhaust manifolds, and just fill that open space with a bb's sized blob of weld?
If that would work, then I don't need to worry about breaking bolts and I can get those damn lines out of my way. Make the engine bay look a little cleaner too!

The air injection is totally in-operable as the pump seized up back when the previous owner had the jeep. I'm not ever going to need it. I just want to seal this leak and get rid of those little lines.
__________________
1990 Grand Wagoneer-"The Crapwagon"
AMC 360, TF727, NP229, 3.31gears, 2" lift
...still kinda rusty

The other's
1987 Dodge Dakota LE 3.9,A999TF,3.90gears(DD)
1994 GMC 'Burban L05-5.7,4L60E,3.73gears(DD)
2001 Jeep Cherokee Sport 4.0,AW4,3.73gears(Limbo)178K
Reply With Quote
  #2  
Old 04-09-2019, 04:36 AM
wiley-moeracing wiley-moeracing is offline
350 Buick
 
Join Date: Feb 15, 2010
Location: arizona
Posts: 984
Yes, I did that for a customer a while back in the same situation.
Reply With Quote
  #3  
Old 04-09-2019, 11:02 AM
ZackN920's Avatar
ZackN920 ZackN920 is offline
350 Buick
 
Join Date: Nov 18, 2015
Location: Stephenson County, IL
Posts: 844
Awesome, I'll probably do it this afternoon after I clean the spark plugs in my pickup truck... Damn thing fouled em' up.


Wow, you had to do that for someone in Arizona? That sucks, that's supposed to be the rust free area of the country! Being that my Jeep is an IL lifer, it makes some sense that it's rusty...
__________________
1990 Grand Wagoneer-"The Crapwagon"
AMC 360, TF727, NP229, 3.31gears, 2" lift
...still kinda rusty

The other's
1987 Dodge Dakota LE 3.9,A999TF,3.90gears(DD)
1994 GMC 'Burban L05-5.7,4L60E,3.73gears(DD)
2001 Jeep Cherokee Sport 4.0,AW4,3.73gears(Limbo)178K
Reply With Quote
  #4  
Old 04-10-2019, 04:33 AM
wiley-moeracing wiley-moeracing is offline
350 Buick
 
Join Date: Feb 15, 2010
Location: arizona
Posts: 984
We still have snow country up north, that's where this customers jeep was from.
Reply With Quote
  #5  
Old 04-10-2019, 07:21 AM
JeepJeepster JeepJeepster is offline
350 Buick
 
Join Date: Sep 04, 2014
Location: Kentucky
Posts: 822
Might could just use some vice grips to crimp it shut.

It really cleans up the engine bay when you remove all of that stuff.
__________________
2004 Jeep Liberty
1998 Jeep ZJ 5.9
1994 Jeep ZJ I6
1989 Jeep Grand Wagoneer 360
Reply With Quote
  #6  
Old 04-14-2019, 05:26 PM
ZackN920's Avatar
ZackN920 ZackN920 is offline
350 Buick
 
Join Date: Nov 18, 2015
Location: Stephenson County, IL
Posts: 844
OK wiley

JeepJeepster- Not where the hole is. Its hard to explain where the hole is and a pic would be easier, but I have no pic atm. Could cut the lines and do that to them, but that just makes things uglier under the hood and a higher potential for me to cut myself when working under the hood.

What I plan to do will remove it all-other than the actual bolt heads. If I try to take the air injection tubes off like you normally would, this would blossom into a huge project. That would lead me to pulling the heads so I can put them on the bench and drill out broken rusted manifold bolts. I don't want to do all that.
__________________
1990 Grand Wagoneer-"The Crapwagon"
AMC 360, TF727, NP229, 3.31gears, 2" lift
...still kinda rusty

The other's
1987 Dodge Dakota LE 3.9,A999TF,3.90gears(DD)
1994 GMC 'Burban L05-5.7,4L60E,3.73gears(DD)
2001 Jeep Cherokee Sport 4.0,AW4,3.73gears(Limbo)178K
Reply With Quote
  #7  
Old 04-15-2019, 04:35 AM
wiley-moeracing wiley-moeracing is offline
350 Buick
 
Join Date: Feb 15, 2010
Location: arizona
Posts: 984
you should not have to remove the heads, take off the exhaust manifolds instead, if the bolts for the injection tubes are rusted out, buy some used exhaust manifolds, a lot easier and less time than trying to repair.
Reply With Quote
  #8  
Old 04-15-2019, 05:56 PM
nograin's Avatar
nograin nograin is offline
304 AMC
 
Join Date: Dec 19, 2000
Location: Philadelphia, Pa., USA
Posts: 2,013
Quote:
Originally Posted by wiley-moeracing
you should not have to remove the heads, take off the exhaust manifolds instead, if the bolts for the injection tubes are rusted out, buy some used exhaust manifolds, a lot easier and less time than trying to repair.

The hardest part of removing the exhaust manifolds with the engine in may be the head pipes.

Once the manifolds are on the bench, I had great luck removing the banjo bolts with an impact wrench. Easier and less destortion to the bolts than the time I removed them with the manifold on the engine.

I did have to clean up the thread on one hole. The rest were fine. All depends what you find when you take them off.
http://www.ifsja.org/forums/vb/showthread.php?t=181535

http://www.ifsja.org/forums/vb/showthread.php?t=184771
__________________
'85 Grand Wagoneer
360 727auto, NP229
body by beer (PO)
carries wood inside
no "wood" outside
My other car is a fish
Reply With Quote
  #9  
Old 04-17-2019, 12:51 PM
rang-a-stang's Avatar
rang-a-stang rang-a-stang is offline
304 AMC
 
Join Date: Oct 31, 2016
Location: Camarillo, CA
Posts: 2,302
Quote:
Originally Posted by ZackN920
...I'm sure the injection bolts WONT come out. So don't even tell me-"just unbolt it and put regular bolts in". That's not happening with this Jeep. and no, I don't want, or plan to pull the manifolds...
HAHAHA!!! I hear you! I broke 2 of them trying to get my banjo bolts out. It was a total PITA to drill and rethread them. I say cut the tube at the banjo, tap the hole where the tube was and throw a bolt down the hole. If that doesn't hold, weld that hole shut with a nice big blob.
__________________
79 Cherokee Chief, barely runs
(Cherokee Build Thread)
11 Nissan Pathfinder Silver Edition 4x4
09 Mazdaspeed3 Grand Touring
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Broken air injection bolts coreyw454 General FSJ Tech 30 01-26-2018 11:01 AM
Air injection hose / check valve Beach_Dude General FSJ Tech 4 03-14-2011 11:11 AM
Source for air injection tube washers elskeptico General FSJ Tech 3 02-10-2011 06:00 PM
Air injection tubes Locked and Loaded General FSJ Tech 16 12-24-2007 10:25 PM
Air injection tube removal marcd General FSJ Tech 9 12-02-2003 06:37 AM


All times are GMT -6. The time now is 12:38 AM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
corner corner