 |
|
06-17-2022, 05:45 AM
|
 |
350 Buick
|
|
Join Date: Jan 15, 2004
Location: TUG HILL, NEW YORK
Posts: 1,483
|
|
|
J-20 REAR AXLE SHAFT
I need one rear axle shaft for the " centered Dana 60 " vs. the offset unit. The axle shaft I need is about 36inches long from the spline end to the inner flange lip
__________________
1977 CJ 7 360 T-18 IHC D300 FARM TRUCK NY
1985 CJ 7 AMC 401, CLARK 285SV 5 SPEED, DANA 60, DANA 44, RUBICON 4.5 LIFT. 37 KRAWLERS
1987 J-20 401 90% COMPLETED.
1985 J-20 360 6 inch lift, 37's plow truck
1986 J-20 360 stock well rusted plow truck
1970 AMX CURRENT PROJECT
|
06-17-2022, 12:51 PM
|
 |
327 Rambler
|
|
Join Date: Feb 09, 2014
Location: Schoorl ,the Nederlands
Posts: 570
|
|
|
How many splines does the axle need to have?
__________________
Jeep "because mother nature hates flat roads to"
http://www.ifsja.org/forums/vb/showthread.php?t=180974
99' Dodge ram 2500 4x4 crew cab 5.9 Cummins ,backup work truck for now
73' Jeep J4000 (named Heep or Desert Dragon) amc 360 V8 converted to LPG with T15/D20 (was my daily work truck for thirteen years and is getting major overhaul at the moment!)
80' Jeep cj5 350 V8 Chevy/sm420/D300 project
70/71 Jeep J4000 parts truck with Buick 350
Former vehicles:
85' Volkswagen caddy mk1 1.6 diesel.
83 Toyota land cruiser BJ42 3.4 diesel.
|
06-18-2022, 06:52 PM
|
|
350 Buick
|
|
Join Date: Jan 15, 2004
Location: TUG HILL, NEW YORK
Posts: 1,483
|
|
|
SPLINE COUNT
30 spline
__________________
1977 CJ 7 360 T-18 IHC D300 FARM TRUCK NY
1985 CJ 7 AMC 401, CLARK 285SV 5 SPEED, DANA 60, DANA 44, RUBICON 4.5 LIFT. 37 KRAWLERS
1987 J-20 401 90% COMPLETED.
1985 J-20 360 6 inch lift, 37's plow truck
1986 J-20 360 stock well rusted plow truck
1970 AMX CURRENT PROJECT
|
06-19-2022, 03:03 AM
|
|
327 Rambler
|
|
Join Date: Feb 09, 2014
Location: Schoorl ,the Nederlands
Posts: 570
|
|
https://www.ebay.com/itm/27399438676...AOSwXjVdcB3 X
Don't know how accurate measurements are , but maybe this could be a solution!?
__________________
Jeep "because mother nature hates flat roads to"
http://www.ifsja.org/forums/vb/showthread.php?t=180974
99' Dodge ram 2500 4x4 crew cab 5.9 Cummins ,backup work truck for now
73' Jeep J4000 (named Heep or Desert Dragon) amc 360 V8 converted to LPG with T15/D20 (was my daily work truck for thirteen years and is getting major overhaul at the moment!)
80' Jeep cj5 350 V8 Chevy/sm420/D300 project
70/71 Jeep J4000 parts truck with Buick 350
Former vehicles:
85' Volkswagen caddy mk1 1.6 diesel.
83 Toyota land cruiser BJ42 3.4 diesel.
|
06-19-2022, 07:24 PM
|
|
350 Buick
|
|
Join Date: Jan 15, 2004
Location: TUG HILL, NEW YORK
Posts: 1,483
|
|
|
AXLE
I THINK THIS COULD WORK!!!!
__________________
1977 CJ 7 360 T-18 IHC D300 FARM TRUCK NY
1985 CJ 7 AMC 401, CLARK 285SV 5 SPEED, DANA 60, DANA 44, RUBICON 4.5 LIFT. 37 KRAWLERS
1987 J-20 401 90% COMPLETED.
1985 J-20 360 6 inch lift, 37's plow truck
1986 J-20 360 stock well rusted plow truck
1970 AMX CURRENT PROJECT
|
06-23-2022, 12:10 PM
|
|
Jeep Doctor
|
|
Join Date: Apr 09, 2000
Location: Providence, RI
Posts: 8,319
|
|
Quote:
|
Originally Posted by JERSEY JOE
I THINK THIS COULD WORK!!!!
|
The flange that bolts to the hub on our J-20s is much smaller in diameter and bolt-pattern than most other D60 full-float rear axles, including the Dodge axles, so even if the shaft was the same length and splines, it might not bolt to the hub.
Our axle uses the same flange-size as the D60s used on Chevy trucks up through '72, when they were replaced by GM's own 14-bolt axle. You'd have better luck finding a compatible axle shaft from one of those applications, but to be honest, another J-20 axle will be your best bet. |
06-23-2022, 02:37 PM
|
|
350 Buick
|
|
Join Date: Jan 15, 2004
Location: TUG HILL, NEW YORK
Posts: 1,483
|
|
|
AXLE SHAFT
I agree that a Jeep axle would be the best but have not despite my best efforts found one. I still have time since the project is not yet rolling but looks like I will have to send my sample axle out to have one made.
__________________
1977 CJ 7 360 T-18 IHC D300 FARM TRUCK NY
1985 CJ 7 AMC 401, CLARK 285SV 5 SPEED, DANA 60, DANA 44, RUBICON 4.5 LIFT. 37 KRAWLERS
1987 J-20 401 90% COMPLETED.
1985 J-20 360 6 inch lift, 37's plow truck
1986 J-20 360 stock well rusted plow truck
1970 AMX CURRENT PROJECT
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -6. The time now is 07:27 AM.
|
