Does anyone know where to get the bolts for the smog air injection tubes? I've tried a couple parts places but no luck.
air injection tube bolts
Collapse
X
-
air injection tube bolts
Perry
78 Cherokee WT 401/TH400/D20, Edelbrock Performer intake, Edelbrock 1400 carb, D44 front & rear, 4" Skyjacker Softride, 2" body, 33x12.5 BFG MTs on 15x10
88 GW brought back from the dead after sitting for 15 yearsTags: None
-
-
Remove the air tubes and plug the holes with 9/16 bolts.
It's what I tried to do. Until the first bolt disinegrated.
EDIT: Sorry. Didn't see you're from Cali. Air tubes gotta stay I guess. Hippie.1971 J2000 Gladiator - "Bertha"AMC 360 - 2bbl Motorcraft Carb - T-15A 3spd - D20 T-Case - 11" Clutch - D44 front and rear - 4.09 axle ratio** Status - Scrapped **1990 Grand Wagoneer** New - Just learning about her **
-
-
LOL!! Hippie...'91 Grand Wagoneer- New Long Block 05-10 W/ Edelbrock Performer Manifold, Carb, & HEI upgrade w/Taylor wires...and lotsa CHROME!--Chevy S-10 Steering box upgrade--3" body lift--31' BFG's
2006 Harley Davidson 1200 Custom Sportster--
2008 Harley Davidson 1200 Low Sporster
'86 Chevy G20 Van
'96 Pontiac Grand AM
Comment
-
-
Also, check U-pulls and junkyards. Paid 5 bucks for the goofy one on the driver's side that also holds the air tube to Cat. They want 32 bucks for that one new! Then, before you reinstall, run a tap into the exhaust manifold threads. Hard to find the 9/16ths NF tap on the shelf, however, had to order one.Unicef Foster Child sponsored by a Canadian Family
1985 Jeep Grand Wagoneer, excellent original condition.
Comment
-
-
Originally posted by GrenadiersAlso, check U-pulls and junkyards. Paid 5 bucks for the goofy one on the driver's side that also holds the air tube to Cat. They want 32 bucks for that one new! Then, before you reinstall, run a tap into the exhaust manifold threads. Hard to find the 9/16ths NF tap on the shelf, however, had to order one.\'88 gwag,pure stock
Comment
-
-
Member "Greg Taylor" here sold me some SS plugs that have holes in them for safety wire. I believe there for airplane engines. Do a search for him. I bought 7 from Greg them I went to PepBoys and found some copper crush washers to fit. Find Greg and shoot him a PM, tell him I sent you.
The thread is a 9/16-18 and you need like a 1/2 -5/8" long bolt AND GASKET. The problem is, no one sells a 9/16"-18 bolt in less than 1" long.
Member Elliott found some too... CLICK HERELast edited by Artisan; 04-24-2010, 07:20 AM.
Comment
-
-
thanks to all for the info
PerryPerry
78 Cherokee WT 401/TH400/D20, Edelbrock Performer intake, Edelbrock 1400 carb, D44 front & rear, 4" Skyjacker Softride, 2" body, 33x12.5 BFG MTs on 15x10
88 GW brought back from the dead after sitting for 15 years
Comment
-
-
I also got mine from http://www.teamgrandwagoneer.com/. It's just too bad the old banjo bolt heads snapped right off. I broke one and left the rest alone for now. Forced a smaller bolt into the broken banjo bolt and called it good...
Just be ready..."Bessie" 1982 Wagoneer Limited
http://www.ifsja.org/forums/vb/showthread.php?t=120964
Comment
-
Comment