If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
No original switch, it has switches that can be easily replaced from auto parts store. Look at the build link in my signature and you can see pictures of the harness an switches. serehill should be in her in short order.
Life happens while you are making plans...............
You can use the original dash switch if you want to, It's a simple conversion. The save the front switch for a spare.
80 Cherokee
360 ci 727 with
Comp cams 270 h
NP208
Edlebrock performer intake
Holley 4180
Msd total multi spark.
4" rusty's springs
Member, FSJ Prissy Restoration Association
If you can't make it better why waste your time. No use repeating the orignal mistakes. I'm to old to push it that's why.
Are these upgrades still being made? Hope to finally complete this upgrade in the next couple of months. Things came up and unfortunately this project was put on the back burner
Sorry for the delay I built one last weekend. I'm just like the Energizer DUMMY I keep going & going. Pun intended.
I am interested in a set up as well. I just completed a complete rewire with an EZ wiring kit.
So I will be starting from scratch I am interested in a type 2.
I will eventually just remove the rear switch completely and have it run from the front only.
Memo
Memo
US Marine
First jeep ever and loving every second
I am interested in a set up as well. I just completed a complete rewire with an EZ wiring kit.
So I will be starting from scratch I am interested in a type 2.
I will eventually just remove the rear switch completely and have it run from the front only.
Memo
We can hook you up PM sent. I don't have a tailgate control either.
80 Cherokee
360 ci 727 with
Comp cams 270 h
NP208
Edlebrock performer intake
Holley 4180
Msd total multi spark.
4" rusty's springs
Member, FSJ Prissy Restoration Association
If you can't make it better why waste your time. No use repeating the orignal mistakes. I'm to old to push it that's why.
Is there one that can unlock the doors and do the tailgate with the same remote?
You can use a viper system if you modify the to my tailgate system it converts the wiring to with a simple 3 wire most alarms can control. I have this is in my Cherokee. If you read the thread the information's there.
80 Cherokee
360 ci 727 with
Comp cams 270 h
NP208
Edlebrock performer intake
Holley 4180
Msd total multi spark.
4" rusty's springs
Member, FSJ Prissy Restoration Association
If you can't make it better why waste your time. No use repeating the orignal mistakes. I'm to old to push it that's why.
You can use a viper system if you modify the to my tailgate system it converts the wiring to with a simple 3 wire most alarms can control. I have this is in my Cherokee. If you read the thread the information's there.
80 Cherokee
360 ci 727 with
Comp cams 270 h
NP208
Edlebrock performer intake
Holley 4180
Msd total multi spark.
4" rusty's springs
Member, FSJ Prissy Restoration Association
If you can't make it better why waste your time. No use repeating the orignal mistakes. I'm to old to push it that's why.
I have completed 10 tailgate relay control systems & I'll be putting more information out on these over the next few days & populate it similar to the headlight harness with details. Update 305 built & sold
I'll complete documentation & have it up tomorrow.
There will be 3 styles available starting out to see where the market goes. These are a complete rewire & a little harder than the headlight harness but well worth the effort. They have been in operation over the last 3 years so they are time tested. There is some info on these in the relayed headlight section.
Type #1 will be a totally hardwired version which will operate like stock switch on the dash & tailgate switch. you can used upgraded switches or your stock switches.
$100.00
Type 2 will be a totally hardwired with a wirless remote. It will have all the options of # 1 with the wireles.
$140
Type 3 wound up being a last thought & is interesting because it's really easy to install & get going. It's a totally remote where you don't wire up either switch the remote is the only thing that opens it.
$100.00
Just added type four by request. this one will just have the controller & battery power wire only. It can be used with the exsitng wire in the harnesses for the OEM guy or the guy that knows his wiring is good. The power feed & the way to factory system operates is the problem this one enhances power & totally changes the way the switches operate off of a simple 3 wire system.
70.00
The design is modular & can be done in any combination if you didn't want the tail gate switch you can easily remove the wiring. The dash switch can be eliminated also. The remote can be done later.
The harness could be put in in one day if you stayed busy. It's like the headlight harness is built of quality products & is electrically protected & the control circuit is even fused to protect from mistakes installing the unit.
It also has the capability of utilizing the factory door safety switch on the tailgate. It is built to bypass the switch but has a circuit that can very simply be changed to operate the safety. You can also used replacement or the stock switches. They will used to operate relay instaed of the motors directly which is the original systems downfall.
GI John has the 2nd prototype & Could be contacted by PM if you wish to discuss one. He has had in operation for 11 months. John helped me through the development & install stages of the build/ design. He has the wired remote system Type #2. PM him with any questions you may have he's the only one besides me that has installed one.
Breaker circuit with auto reset instead of fuse. for main power.
80 Cherokee
360 ci 727 with
Comp cams 270 h
NP208
Edlebrock performer intake
Holley 4180
Msd total multi spark.
4" rusty's springs
Member, FSJ Prissy Restoration Association
If you can't make it better why waste your time. No use repeating the orignal mistakes. I'm to old to push it that's why.
Comment