International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums

Showing results 1 to 20 of 20
Search took 0.01 seconds.
Search: Posts Made By: Jeep madness
Forum: General FSJ Tech 02-14-2011, 09:23 PM
Replies: 4
Views: 334
Posted By Jeep madness
The problem with a J4000, is the frame width it...

The problem with a J4000, is the frame width it the back, and the springs in front are out side of the frame. In the back, the leaf spring are 50 1/2''apart. Its hard to find an axle wide enough,...
Forum: Homegrown Vendors: (Members who produce FSJ related items) 02-05-2011, 07:28 PM
Replies: 223
Views: 109,705
Posted By Jeep madness
Got my truck running last weekend, put headers...

Got my truck running last weekend, put headers and HB on today. Wow!!! I had to pick my teeth out of the steering wheel. Thanks for you help.


Now, I would like an other for the wife's Cherokee....
Forum: General FSJ Tech 01-31-2011, 09:10 PM
Replies: 32
Views: 4,876
Posted By Jeep madness
Got truck up and running again. I put a Comp...

Got truck up and running again. I put a Comp cam,and Comp cam timing set and Mallory dis. Drove 15 miles to the house and pulled the dis. and gear is nice and wet.

I took the motor apart really...
Forum: General FSJ Tech 01-11-2011, 08:28 PM
Replies: 32
Views: 4,876
Posted By Jeep madness
I'm not messing around! I'm using this as an...

I'm not messing around! I'm using this as an opportunity. I ordered a Comp Cam ex256 cam, timing chain, headers, Mallory dis, and coil. Going to re cam to move torque up the rpm range, for pulling...
Forum: General FSJ Tech 01-10-2011, 07:30 PM
Replies: 32
Views: 4,876
Posted By Jeep madness
Talked to Mat at Bulltear, after talking it over...

Talked to Mat at Bulltear, after talking it over with him, I'm looking for a stopped up oil passage. I got another set of gears coming. Wish me luck!!!
Forum: General FSJ Tech 01-09-2011, 07:21 AM
Replies: 32
Views: 4,876
Posted By Jeep madness
The motor has the original timing cover. The...

The motor has the original timing cover. The distributor gear is missing teeth on one side. I will try to get some pictures of it.
Forum: General FSJ Tech 01-08-2011, 07:18 PM
Replies: 32
Views: 4,876
Posted By Jeep madness
I did that before I put it in with the new gears....

I did that before I put it in with the new gears. It is the same dimensions. I looked at every thing close before I put the motor back together. Changing the gear is a big pain! I did not want to do...
Forum: General FSJ Tech 01-08-2011, 06:05 PM
Replies: 32
Views: 4,876
Posted By Jeep madness
I only changed the distributor. The motor only...

I only changed the distributor. The motor only has about 8000 miles on it. I thought getting rid of the points dis. would help performance. I use the truck hard when I use it, pulling tractors, hay...
Forum: General FSJ Tech 01-08-2011, 02:55 PM
Replies: 32
Views: 4,876
Posted By Jeep madness
The distributor was all the way in. I have to do...

The distributor was all the way in. I have to do it all over again!!! Monday I'm going to call Bulltear.
Forum: General FSJ Tech 01-08-2011, 02:47 PM
Replies: 32
Views: 4,876
Posted By Jeep madness
Bulltear distributor gear set problem.

I,m so mad I can't even think straight!!! My truck ate the dizzy drive gears last month after I installed a HEI dizzy. Well lesson learned, transfer the gear form your old dis. to new dis.. Well...
Forum: General FSJ Tech 01-08-2011, 07:27 AM
Replies: 40
Views: 1,575
Posted By Jeep madness
I have seen a new pilot bushing a little snug....

I have seen a new pilot bushing a little snug. Mainly the China ones. It will cause the input shaft to turn just fast enought to not go into gear. Before you put the trans, start it in gear with the...
Forum: General FSJ Tech 12-22-2010, 07:25 PM
Replies: 12
Views: 2,257
Posted By Jeep madness
I did the same swap in my J4000 about 3 years...

I did the same swap in my J4000 about 3 years ago. I had the t-case shifter, spacer, and correct input shaft off a t-18 out of another J truck. I Had the rear drive shaft shortened 2'' and had a new...
Forum: Fuel Injection 12-17-2010, 07:04 PM
Replies: 37
Views: 3,626
Posted By Jeep madness
I have Holley 2D Projection on a 360 in my CJ7...

I have Holley 2D Projection on a 360 in my CJ7 for about 4 years now. It has given no trouble at all. Any injection set up will give you trouble if its not set up properly. My system runs great when...
Forum: General FSJ Tech 12-05-2010, 09:47 PM
Replies: 32
Views: 983
Posted By Jeep madness
I looked and measured the end of the distributor...

I looked and measured the end of the distributor before I dropped it in. I did not notice the pitch on the gear was different until I pulled it out. Now the cam gear is toast. Live and learn!
Forum: General FSJ Tech 12-05-2010, 08:16 PM
Replies: 32
Views: 983
Posted By Jeep madness
I've had 2 other poeple teel me to get a Bulltear...

I've had 2 other poeple teel me to get a Bulltear set, so that is what I'm going with too. Mine is going to have to wait until after X-mas though.
Forum: General FSJ Tech 12-05-2010, 07:56 PM
Replies: 32
Views: 983
Posted By Jeep madness
I feel your pain!!!

I just "up graded" to a HEI distributor. I had the same thing happen. The dizzy had a gear on it and I just dropped it in. 10 miles later, a roll back is bring me back to the house. It sucks to cause...
Forum: General FSJ Discussion 09-08-2010, 09:18 PM
Replies: 23
Views: 1,510
Posted By Jeep madness
All I can say is, OH DEAR!!! I have I 72...

All I can say is, OH DEAR!!!



I have I 72 J-4000 that I use to tow and haul daily. I love it. You have more to start with then I do. Good luck on the repair.
Forum: General FSJ Discussion 09-08-2010, 08:57 PM
Replies: 33
Views: 1,063
Posted By Jeep madness
I get worried when my Jeep truck doesn't leak!...

I get worried when my Jeep truck doesn't leak! That means its out of oil.
Forum: General FSJ Tech 07-27-2010, 03:15 PM
Replies: 261
Views: 266,849
Posted By Jeep madness
83 Cherokee, Skyjacker 4" lift kit,...

83 Cherokee, Skyjacker 4" lift kit, Bushwacker XJ cut out flares, painted to match. 15 X 10 rims with 35 X 12.50 tires. If its put in a twist, it will rub a little. Its my wife's, and she runs the...
Forum: General FSJ Tech 07-27-2010, 11:33 AM
Replies: 12
Views: 904
Posted By Jeep madness
^^^I have always used 3M Strip caulk to hold the...

^^^I have always used 3M Strip caulk to hold the vapor shields. Is similar to what was originally used. You can find it at most auto supply or parts stores.
Showing results 1 to 20 of 20

 
Forum Jump

All times are GMT -6. The time now is 06:19 PM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
corner corner