International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums
Reload this Page Search Results

Page 1 of 3 1 23 >
Showing results 1 to 25 of 61
Search took 0.01 seconds. Search: Posts Made By: PBG928
Forum: General FSJ Tech 07-01-2019, 02:40 PM
Replies: 7
Views: 547
Posted By PBG928
Check two lines on passenger side of engine that...

Check two lines on passenger side of engine that vent fuel tank. Plug temporarily and see if performance improves.
Forum: Fuel Injection 06-25-2019, 07:08 AM
Replies: 15
Views: 1,950
Posted By PBG928
I don't think your stalling is due to timing...

I don't think your stalling is due to timing control. This is my second sniper system after the initial Howell efi. Howell had a DUI distributor, first sniper has an MSD with no box, and third had a...
Forum: Fuel Injection 06-24-2019, 03:51 PM
Replies: 15
Views: 1,950
Posted By PBG928
I just did the Holley 2300 with Hyperspark and...

I just did the Holley 2300 with Hyperspark and Robbmc powersurge fuel system. If you want to modify fuel lines and intake at tank you do not need the
Robbmc. Once dialed in it runs like a dream....
Forum: General FSJ Tech 06-24-2019, 03:10 PM
Replies: 1
Views: 375
Posted By PBG928
Solved missing issue

Solved it!. Shout out to Holley tech support for helping. I run a Sniper 2300 and put in Holley Hyperspark system which includes a coil, Distributor and ignition box. All plug and play with Sniper...
Forum: General FSJ Tech 06-18-2019, 05:59 PM
Replies: 1
Views: 375
Posted By PBG928
85 GW Engine missing

My 85 has a rebuilt motor with Holley Sniper that I recently added. vibrates and shakes at low idle and when accelerating. Checked time, replaced plugs and wires, New DUI distributor. Thought it may...
Forum: General FSJ Tech 05-26-2019, 07:29 AM
Replies: 11
Views: 879
Posted By PBG928
Yes it was the ground wire that is screwed into...

Yes it was the ground wire that is screwed into drivers inside wheel well that had been cut. Got it working so I can move car around.
Forum: General FSJ Tech 05-09-2019, 06:05 AM
Replies: 7
Views: 217
Posted By PBG928
It is tight but you can remove it with a plastic...

It is tight but you can remove it with a plastic prybar, Replace it with Steele https://www.steelerubber.com/extrusion-dense-70-2818-60. It is an identical match with tape on one side to hold it...
Forum: General FSJ Tech 05-09-2019, 06:00 AM
Replies: 14
Views: 447
Posted By PBG928
I had my 89 GW blasted with beads and water using...

I had my 89 GW blasted with beads and water using a $40k blasting machine. Worked out great. Yes there is left over sand that can be blown or vacuumed out. But nothing does a better job on rust...
Forum: Fuel Injection 05-02-2019, 01:44 PM
Replies: 20
Views: 3,160
Posted By PBG928
Finally got Robbmc and Holley Sniper installed....

Finally got Robbmc and Holley Sniper installed. Engine actually started. Have to fix a few other things before I can let it warm up and start learning. LCD screen is way cooler than the 1950 style...
Forum: General FSJ Tech 04-29-2019, 07:55 AM
Replies: 4
Views: 328
Posted By PBG928
Get this from Steele Rubber. Identical profile...

Get this from Steele Rubber. Identical profile with double stick tape. Works great.
https://www.steelerubber.com/extrusion-dense-70-2818-60
Forum: General FSJ Tech 04-29-2019, 07:43 AM
Replies: 12
Views: 1,285
Posted By PBG928
Gave up and welded section of roof from parts car...

Gave up and welded section of roof from parts car in and added new headliner. You might try this fellow as he bought the old sunroof and has experience with them. h-terrazas@sbcglobal.net
Forum: Fuel Injection 04-04-2019, 06:32 PM
Replies: 20
Views: 3,160
Posted By PBG928
Getting ready to install the Holley Sniper and...

Getting ready to install the Holley Sniper and the Robbmc mentioned above. with this set up do I really need the charcoal filter?
Forum: General FSJ Discussion 03-26-2019, 11:09 AM
Replies: 13
Views: 676
Posted By PBG928
I took the material on the cover of the mirror...

I took the material on the cover of the mirror off, cleaned off glue then sprayed the lid with SEM paint to match dash such as tan or burgandy. Of course recovered entire visor as well with new...
Forum: General FSJ Discussion 01-01-2019, 11:31 AM
Replies: 6
Views: 501
Posted By PBG928
I compared my Team GW wiper arm with one I pulled...

I compared my Team GW wiper arm with one I pulled at Junkyard off of a 89 GW. The hole is smaller on the junkyard wiper arm than the TGW arm, I looked closely at shaft and could still see the...
Forum: General FSJ Discussion 12-31-2018, 08:04 PM
Replies: 6
Views: 501
Posted By PBG928
Makes sense. Will try it. thanks.

Makes sense. Will try it. thanks.
Forum: General FSJ Discussion 12-31-2018, 12:56 PM
Replies: 6
Views: 501
Posted By PBG928
Oem motor, shaft is too small.

Oem motor, shaft is too small.
Forum: General FSJ Discussion 12-30-2018, 05:09 PM
Replies: 6
Views: 501
Posted By PBG928
Couple of picks of shaft

https://www.flickr.com/gp/141914768@N04/835beR
https://www.flickr.com/gp/141914768@N04/44xqWz
Forum: General FSJ Discussion 12-30-2018, 04:56 PM
Replies: 6
Views: 501
Posted By PBG928
Rear wiper motor shaft for 89 GW

Rear wiper motor works but shaft seems too small for new TGW arm made for rear or one I pulled at junkyard. Is there a bushing or sleeve that goes over shaft as wiper arm is too big.
Forum: General FSJ Tech 11-17-2018, 07:18 PM
Replies: 10
Views: 614
Posted By PBG928
Check ground wire on drivers wheel well as this...

Check ground wire on drivers wheel well as this is main ground for most circuits. One black wire with ring terminal next to washer tank.
Forum: FSJ-PRIS 10-05-2018, 02:58 PM
Replies: 4
Views: 1,850
Posted By PBG928
Air Cleaner was satin to flat black, Gloss looks...

Air Cleaner was satin to flat black, Gloss looks better. Engine light was silver.
Forum: General FSJ Tech 10-02-2018, 11:21 AM
Replies: 4
Views: 718
Posted By PBG928
Try this from Steele Rubber profile is identical...

Try this from Steele Rubber profile is identical to original, peel and stick to apply. https://www.steelerubber.com/extrusion-dense-70-2818-60
Forum: General FSJ Tech 09-25-2018, 06:39 PM
Replies: 11
Views: 879
Posted By PBG928
Smile Success Updated: Its the ground wire stupid!

Thought everything was ok after I removed the door chime. Went to 12+volts then dropped back to 8. I had removed the front body cap to have all body parts blasted and painted due to prior damage on...
Forum: General FSJ Tech 09-22-2018, 08:41 AM
Replies: 11
Views: 879
Posted By PBG928
Success

Unwrapped electrical tape covering engine wiring found one cut wire that looked old. Got under dash and pulled door chime which had two broken rusted terminals stuck in fuse block. Now I have full...
Forum: General FSJ Tech 09-19-2018, 11:21 AM
Replies: 11
Views: 879
Posted By PBG928
What's odd is everything worked for about a day...

What's odd is everything worked for about a day then voltage dropped down. I get it on the windows and headlights as I have been there and done that, I hate getting under the dash but will start....
Forum: General FSJ Tech 09-19-2018, 07:54 AM
Replies: 11
Views: 879
Posted By PBG928
86 GW wiring problems, low voltage

My newly acquired 86 GW has 13v at battery and at new starter solenoid on fender. I have replaced battery cables and positive cable running from solenoid to starter.(later models had a relay on the...
Showing results 1 to 25 of 61
Page 1 of 3 1 23 >

 
Forum Jump

All times are GMT -6. The time now is 05:09 AM.

Contact Us - International Full Size Jeep Association - Archive - Top

Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
corner IFSJA.org hosting provided by Golden Computer Service.
© 2000-2006 IFSJA Site Staff.   Jeep® is a registerd trademark of DaimlerChrysler. 		corner