International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums

Showing results 1 to 25 of 500
Search took 1.38 seconds.
Search: Posts Made By: rocklaurence
Forum: General FSJ Tech 11-14-2019, 07:46 AM
Replies: 9
Views: 181
Posted By rocklaurence
Yep, that looks like it. I didnt know that...

Yep, that looks like it. I didnt know that anyone made a replaement.
Forum: General FSJ Tech 11-12-2019, 09:04 AM
Replies: 2
Views: 145
Posted By rocklaurence
You need to match the gears. After that...

You need to match the gears. After that consideration, most 3/4 ton eight Lug truck axles will work. Most are 65"-ish WMS-WMS and you'll likely need to move the spring perches and replace the...
Forum: General FSJ Tech 11-12-2019, 08:49 AM
Replies: 50
Views: 1,921
Posted By rocklaurence
Regarding Trans fluid temps, I bypass the...

Regarding Trans fluid temps, I bypass the radiator on all my vehicles because the engine is running at 195/210 degrees and the danger zone for a trans is 220. With a separate cooler of 24000 GVW...
Forum: General FSJ Tech 11-12-2019, 08:27 AM
Replies: 12
Views: 247
Posted By rocklaurence
I ran a Power Master 1 wire until the bearings...

I ran a Power Master 1 wire until the bearings went out. Since then Ive run the Advance Auto single wire in two trucks without any issues. However, the Advance Auto units are only 40 amps but I...
Forum: General FSJ Tech 11-12-2019, 08:17 AM
Replies: 11
Views: 177
Posted By rocklaurence
I have a Red Holley on one truck and a Holley...

I have a Red Holley on one truck and a Holley Mighty Mite on the second. They both have been running for 5-6 years now. Look for a carb unit with 5-7 psi. Also, run a ground from the battery with...
Forum: General FSJ Tech 11-12-2019, 08:10 AM
Replies: 9
Views: 181
Posted By rocklaurence
Nope, there's a module with a switch that sets...

Nope, there's a module with a switch that sets inside the plenum that has a Temp' tube with it. It senses the temp' and cycles the compressor. Your AC control panel should have two switches: Fans...
Forum: General FSJ Tech 10-25-2019, 09:14 AM
Replies: 1
Views: 158
Posted By rocklaurence
I saw one installed on a Power Nation Bronco...

I saw one installed on a Power Nation Bronco project [maybe a Blazer]. They beat the piss out of it off road and commented on how well it was running. I do know that it has center hung floats and...
Forum: General FSJ Tech 10-13-2019, 06:32 AM
Replies: 10
Views: 512
Posted By rocklaurence
IMO, your doing it the right way. I had to patch...

IMO, your doing it the right way. I had to patch and box my CJ5 frame and did it exactly like you. However, I strapped the top and bottom of the frame and welded in two cross members as front and...
Forum: General FSJ Tech 09-14-2019, 07:52 AM
Replies: 50
Views: 1,921
Posted By rocklaurence
You'll need 7/8" spacer and longer mounting...

You'll need 7/8" spacer and longer mounting studs because the earlier Tcase input shaft sticks out further than the later NV231/241
Forum: General FSJ Tech 09-14-2019, 07:47 AM
Replies: 3
Views: 316
Posted By rocklaurence
Ebay has them all

Ebay has them all
Forum: General FSJ Discussion 08-10-2019, 09:21 AM
Replies: 21
Views: 954
Posted By rocklaurence
Hey guys, Blown Head gaskets mean other issues as...

Hey guys, Blown Head gaskets mean other issues as well--Worped heads, worped bloch etc. Th mechanic doesnt want to pull the heads to find out that it needs a rebuild. He is letting the owner know...
Forum: General FSJ Tech 08-10-2019, 09:09 AM
Replies: 2
Views: 211
Posted By rocklaurence
The York compressor are noisey. If its...

The York compressor are noisey. If its abnormally noisey, it may be low on oil or is failing.
Forum: General FSJ Discussion 07-30-2019, 12:53 PM
Replies: 21
Views: 954
Posted By rocklaurence
I was real happy with BJs replacement and they...

I was real happy with BJs replacement and they also offer camshaft upgrades, oiling improvements on a rebuild. I went to 3 different Big Stores and none of them could source a core for an AMC V8 but...
Forum: General Chit-Chat 07-22-2019, 11:18 AM
Replies: 11
Views: 688
Posted By rocklaurence
I have a 5" front Long Spring system that Im...

I have a 5" front Long Spring system that Im getting ready to market that is softer than any short [47"] spring out there and has 10-12" of axle travel. It replaces the spring mounts,...
Forum: General FSJ Discussion 07-22-2019, 11:09 AM
Replies: 6
Views: 540
Posted By rocklaurence
Yes, Im interested in this also. Would a new set...

Yes, Im interested in this also. Would a new set of TJ/MJ front belts work in our FSJs? You can get those cheap online or find them in a salvage yard.
Forum: General Chit-Chat 07-22-2019, 11:05 AM
Replies: 20
Views: 1,322
Posted By rocklaurence
My 1980 Chrokee wide track Restomod. We replaced...

My 1980 Chrokee wide track Restomod. We replaced all the rotted metal, painted everything Louden Gree [except the front fenders]. Dash and front seats are re-done, new motor with AX15/NP208, 33x9.5...
Forum: General FSJ Tech 05-20-2019, 08:25 AM
Replies: 8
Views: 616
Posted By rocklaurence
Death Wooble-- check the condition of all the...

Death Wooble-- check the condition of all the joints. If they are good, then it is the Caster/toe-in adjustments. The Toe-in should be 1/4"-0" but never pasitive and the Caster needs to be 7-2...
Forum: General FSJ Tech 05-07-2019, 10:35 AM
Replies: 11
Views: 407
Posted By rocklaurence
Is the 144 a single wire with internal regulator?

Is the 144 a single wire with internal regulator?
Forum: General FSJ Tech 05-02-2019, 04:35 AM
Replies: 3
Views: 317
Posted By rocklaurence
The bolt pattern to mount it to the fly wheel is...

The bolt pattern to mount it to the fly wheel is different than a Mopar. Also, the stock stall is 1300 rpm. A 2000 stall is a B&M/TCI high stall model.
Forum: General FSJ Tech 04-27-2019, 07:56 AM
Replies: 13
Views: 462
Posted By rocklaurence
Agreed, but Id like to try some 17" Ansen 5...

Agreed, but Id like to try some 17" Ansen 5 slot mags on a FSJ;)
Forum: Customer Corner: (Vendor product discussions) 04-21-2019, 04:37 PM
Replies: 2
Views: 369
Posted By rocklaurence
I have...

I have these:
https://rocklaurencevintageautoparts.com/products/jeep-np229-twin-stick-shifter-truck-or-wagon
Forum: General FSJ Discussion 03-14-2019, 02:03 PM
Replies: 2
Views: 494
Posted By rocklaurence
Please dont cut-up good WT fenders!!

Please dont cut-up good WT fenders!!
Forum: Build Threads 03-08-2019, 07:17 AM
Replies: 374
Views: 24,263
Posted By rocklaurence
Regarding blood on the fender, my quote is...

Regarding blood on the fender, my quote is "The job aint done until someone bleeds":D
Forum: Homegrown Vendors: (Members who produce FSJ related items) 03-07-2019, 06:47 AM
Replies: 4
Views: 787
Posted By rocklaurence
EP6 is available.. Rear body lift removal and...

EP6 is available.. Rear body lift removal and Rocky's Rant.. Subscribe
https://www.youtube.com/watch?v=ggggjapuqos
Forum: General FSJ Tech 03-05-2019, 07:38 AM
Replies: 42
Views: 2,016
Posted By rocklaurence
Make sure to Rust-proof the inside of all the...

Make sure to Rust-proof the inside of all the metal during assembly. A weldable primer.
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -6. The time now is 04:22 PM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
corner corner