International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: CutterN55
Forum: General FSJ Tech 08-16-2018, 08:20 AM
Replies: 11
Views: 529
Posted By CutterN55
As said above, it's likely the fuel evaporating. ...

As said above, it's likely the fuel evaporating. I had good luck and much better results will this same problem after installing a phenolic spacer under the carb. It keeps heat transfer to the carb...
Forum: General FSJ Tech 11-13-2017, 07:21 AM
Replies: 13
Views: 1,189
Posted By CutterN55
Cracked vacuum ball, or lines is most common...

Cracked vacuum ball, or lines is most common problem. It's a pretty simple system.
Does the heater blower turn on and you just aren't getting air out of the vents?
Vents not switching between modes?...
Forum: General FSJ Tech 08-10-2017, 01:33 PM
Replies: 13
Views: 844
Posted By CutterN55
Those '90 shafts you found are interchangeable....

Those '90 shafts you found are interchangeable. you are good to go.
Do put new bearings, seals, and bearing retainers on there and do both at the same time like was said before.

Why are you...
Forum: General FSJ Tech 08-08-2017, 12:58 PM
Replies: 18
Views: 975
Posted By CutterN55
you can reuse them in a jam but you really should...

you can reuse them in a jam but you really should replace them as they do stretch a little. I can't remember the sizes. I know the one on the front casting is pretty big, different from the others...
Forum: General FSJ Tech 08-08-2017, 06:34 AM
Replies: 13
Views: 844
Posted By CutterN55
absolutely

absolutely
Forum: General FSJ Tech 08-07-2017, 11:19 AM
Replies: 8
Views: 668
Posted By CutterN55
Did you check the Hi/Lo lever on the floor under...

Did you check the Hi/Lo lever on the floor under the seat? Make sure the linkage isn't sloppy there as well.
Forum: Off-Road FSJ Tech 08-07-2017, 11:04 AM
Replies: 10
Views: 1,006
Posted By CutterN55
I ran conversion joints for a while and I think...

I ran conversion joints for a while and I think the joint is probably a large contributor. IIRC the degree of travel is greatly reduced when running the conversion joints. You are running the...
Forum: General FSJ Tech 08-07-2017, 10:30 AM
Replies: 5
Views: 457
Posted By CutterN55
Clean all electrical contacts in the door...

Clean all electrical contacts in the door switches and the motor plugs with acetone or isopropyl alcohol and a wire brush. put it back together, will probably work just fine. these things get really...
Forum: General FSJ Tech 08-07-2017, 10:21 AM
Replies: 12
Views: 772
Posted By CutterN55
I'll bet its the flex plate bolt heads hitting...

I'll bet its the flex plate bolt heads hitting the inspection cover.
Said he didn't have anynoise before poking around in there. when the little tabs get bent just enough it'll do this; tick, tick,...
Forum: General FSJ Tech 08-07-2017, 06:36 AM
Replies: 13
Views: 844
Posted By CutterN55
If you just need the axle shafts, don't worry...

If you just need the axle shafts, don't worry about gear ratios as the rear D44 shaft you need will be a 30 spline in both a potential D44 equipped '86 and what you have in your 88 rear D44. Do...
Forum: General FSJ Discussion 08-03-2017, 09:30 AM
Replies: 13
Views: 1,057
Posted By CutterN55
Call Alcan

Call Alcan
Forum: General FSJ Discussion 07-31-2017, 10:41 AM
Replies: 13
Views: 1,057
Posted By CutterN55
From what I've seen, most of what you'll find...

From what I've seen, most of what you'll find available for 2" - 4" lift height from most of the main stream companies is blocks out back or a combination of 2"blocks and 2" lift springs. It's hard...
Forum: General FSJ Discussion 07-31-2017, 10:22 AM
Replies: 6
Views: 735
Posted By CutterN55
4" grinder and a wire wheel. Get a good look...

4" grinder and a wire wheel. Get a good look at the metal, put some rust killer on it if needed. I got mine down to bare shiny metal and sprayed Rustoleum bedliner on it. then laid the carpet back...
Forum: Off-Road FSJ Tech 06-23-2017, 10:30 AM
Replies: 5
Views: 708
Posted By CutterN55
I think the XJ shaft yokes will work if I...

I think the XJ shaft yokes will work if I remember right. If not you can grab a whole 1310 double-cardon rear and modify it to meet your needs. A Bj's 6" lift does not normally warrant new shafts but...
Forum: General FSJ Tech 06-16-2017, 09:39 AM
Replies: 7
Views: 954
Posted By CutterN55
Thanks brother. Will do. *** email sent with...

Thanks brother. Will do.

***
email sent with pics. waiting to hear back.
Forum: General FSJ Tech 06-03-2017, 03:12 PM
Replies: 7
Views: 954
Posted By CutterN55
This is a CJ7 with my waggy axles in it. 37s are...

This is a CJ7 with my waggy axles in it. 37s are good on a light jeep like a CJ with a 44. I havent been beating on it. I'm rocking now. Im leaning towards low qual bearings. The back retainer ring...
Forum: General FSJ Tech 06-03-2017, 11:50 AM
Replies: 17
Views: 1,446
Posted By CutterN55
Thats what hapens after years of filling up the...

Thats what hapens after years of filling up the radiator with a garden hose with or without coolant. Especially if theres a lot of minerals in your water.

X2 on the permatex to stick the gasket....
Forum: General FSJ Tech 06-03-2017, 11:34 AM
Replies: 7
Views: 954
Posted By CutterN55
Dutchman axle shafts bearing failure?

Couple years ago I purchased some dutchman shafts from BJs for the rear waggy D44 that i rebuilt from bare housing. Up until yesterday they've been flawless with a few wheeling trips, no mud or...
Forum: Off-Road FSJ Tech 05-23-2017, 05:30 AM
Replies: 5
Views: 623
Posted By CutterN55
could be a lot of things. I wonder if the bearing...

could be a lot of things. I wonder if the bearing was replaced and maybe the oil slinger washer wasn't reinstalled? or maybe the pinion preload was too tight as said, ran pinion nut down too tight,...
Forum: General FSJ Tech 05-19-2017, 11:59 AM
Replies: 10
Views: 1,036
Posted By CutterN55
I've seen plenty of my boots use Never-dull or...

I've seen plenty of my boots use Never-dull or Brass-o on their anodized medals, seems to take the shine right off lol!
Forum: General FSJ Tech 05-02-2017, 06:26 AM
Replies: 7
Views: 711
Posted By CutterN55
In my experience with the 1406, sounds like the...

In my experience with the 1406, sounds like the fuel in the bowl is evaporating due to heat after shutdown. I had the same issues with hard starting after it had run hot or sat for a while. A...
Forum: General FSJ Tech 04-26-2017, 06:01 AM
Replies: 11
Views: 1,237
Posted By CutterN55
Stock driveshafts should take you up to about...

Stock driveshafts should take you up to about 6" of lift over stock typically, provided the axle remains in stock location and is not relocated forward. As long as the shackle reversal kit doesn't...
Forum: General FSJ Tech 04-20-2017, 12:58 PM
Replies: 4
Views: 721
Posted By CutterN55
Bj's offroad sells Dutchman shafts for a...

Bj's offroad sells Dutchman shafts for a discounted IFSJA member rate.

You can also order from Dutchman directly.

Just tell them what you need them for.
Forum: General FSJ Discussion 04-20-2017, 06:29 AM
Replies: 8
Views: 1,132
Posted By CutterN55
...and they will raise your engine RPMs at any...

...and they will raise your engine RPMs at any given speed. the faster you go, the higher your engine will rev. The extent will be determined by your differential gearing obviously. If you have 2.73...
Forum: General FSJ Tech 04-11-2017, 01:04 PM
Replies: 23
Views: 1,388
Posted By CutterN55
To put in a Ford tranny (short input) I had to...

To put in a Ford tranny (short input) I had to modify shafts which I did anyway due to a front stretch, crossmember, mounts, get the correct fork for throwout bearing travel, and get the right...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -6. The time now is 12:03 AM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
corner corner