International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums
Reload this Page Search Results

Page 1 of 11 1 23 > Last »
Showing results 1 to 25 of 270
Search took 0.02 seconds. Search: Posts Made By: SCscoutguy
Forum: General FSJ Tech 12-01-2012, 09:58 PM
Replies: 27
Views: 1,576
Posted By SCscoutguy
Well with it being a 68 and a closed knuckle axle...

Well with it being a 68 and a closed knuckle axle then it very well could have had a 5 bolt spindle for all I know as I am not as well educated about the older full size lightline trucks.
Forum: General FSJ Tech 12-01-2012, 05:59 PM
Replies: 27
Views: 1,576
Posted By SCscoutguy
They are not IH axles then. IH axles have 6...

They are not IH axles then. IH axles have 6 spindle bolts for Dana 30's and 8 for Dana 44's.
Forum: General FSJ Tech 11-30-2012, 07:02 PM
Replies: 27
Views: 1,576
Posted By SCscoutguy
The scout D30 axles use the same drag shoes and...

The scout D30 axles use the same drag shoes and hubs as the D44's. In fact everything is the same dimensionally just the spindle on the D30's have 6 bolts and the D44's have 8.
Forum: General FSJ Tech 11-30-2012, 12:30 PM
Replies: 27
Views: 1,576
Posted By SCscoutguy
It will be a Dana 44 they never put 30's in...

It will be a Dana 44 they never put 30's in Travelalls. I have personally never seen Loc-O-Matic hubs on a Travelall even though I know you could get them.
Forum: General FSJ Tech 11-29-2012, 04:32 PM
Replies: 27
Views: 1,576
Posted By SCscoutguy
Those are very hard to find nowadays. They made...

Those are very hard to find nowadays. They made two sizes as far as IH goes. They made 2.25" and 2.125" size. The 2.25" size can still be found sometimes from Super Scout Specialists and IH Parts...
Forum: General FSJ Tech 11-29-2012, 02:55 PM
Replies: 27
Views: 1,576
Posted By SCscoutguy
I have a huge box full of IH hub parts around...

I have a huge box full of IH hub parts around here but like you every single spindle nut that I have is all messed up from someone using a drift or screwdriver and hammer to get the nut off instead...
Forum: Off-Road FSJ Tech 02-08-2010, 10:54 PM
Replies: 27
Views: 1,279
Posted By SCscoutguy
Like everyone has said above my experience with...

Like everyone has said above my experience with the Carter AFB/Edelbrock 1400 series off road has not been the best. There are a bunch of mod's you can do to them to make them better off road but in...
Forum: General FSJ Discussion 02-03-2010, 09:41 PM
Replies: 20
Views: 993
Posted By SCscoutguy
I go to all of the pawn shops in town at least...

I go to all of the pawn shops in town at least once a week so I am on a first name basis with all of the owners. I can pretty much get stuff for barely over what they have in it. Also when I am in...
Forum: General FSJ Discussion 02-02-2010, 04:22 PM
Replies: 20
Views: 993
Posted By SCscoutguy
Before you go around and buy anything new go...

Before you go around and buy anything new go around to the pawn shops in your area and see what they have. I have bought many nice name brand air tools at pawn shops for a faction of the price they...
Forum: General FSJ Discussion 01-31-2010, 06:38 PM
Replies: 45
Views: 3,125
Posted By SCscoutguy
Rick you would hate my midas edition Scout Terra...

Rick you would hate my midas edition Scout Terra then. They even had some models where the carpet was plaid along with the dash cover to go along with everything else in the truck....
Forum: General FSJ Tech 12-19-2009, 04:03 PM
Replies: 9
Views: 1,455
Posted By SCscoutguy
I was going to use this ring from Novak to run a...

I was going to use this ring from Novak to run a D300 behind my AW4 for my 4.0 swap but if that one posted above would work that would save me some coin. I will call them and...
Forum: Off-Road FSJ Tech 11-23-2009, 04:28 PM
Replies: 2
Views: 551
Posted By SCscoutguy
Do a search with the terms "SOA" and...

Do a search with the terms "SOA" and "spring over" and you will find a wealth of knowledge.
Forum: General FSJ Tech 11-11-2009, 08:04 PM
Replies: 14
Views: 1,300
Posted By SCscoutguy
It won't just drop in as it is a totally...

It won't just drop in as it is a totally different engine. You could source a Dodge 4x4 727 and bolt a NP transfer case to it. Really I don't see any advantage to a dodge 360 swap over just putting...
Forum: General FSJ Discussion 11-06-2009, 05:46 PM
Replies: 6
Views: 891
Posted By SCscoutguy
http://www.threadbombing.com/data/media/22/MacGyve...

http://www.threadbombing.com/data/media/22/MacGyver_Approves.jpg
Forum: South East 10-09-2009, 09:00 PM
Replies: 14
Views: 3,347
Posted By SCscoutguy
The title to this thread is "CFSJC is...

The title to this thread is "CFSJC is crap".
Forum: South East 10-09-2009, 05:53 PM
Replies: 14
Views: 3,347
Posted By SCscoutguy
You could have just made a post asking someone to...

You could have just made a post asking someone to activate you here instead of trashing the site like this.
Forum: General FSJ Tech 09-30-2009, 03:00 PM
Replies: 11
Views: 2,469
Posted By SCscoutguy
This is how I did it. I started off with these...

This is how I did it.
I started off with these oil seals from Napa. The one on the right is for the front of the tranny you will not need...
Forum: General FSJ Tech 09-28-2009, 06:49 PM
Replies: 11
Views: 3,319
Posted By SCscoutguy
Here is a good write up on the procedure my buddy...

Here is a good write up on the procedure my buddy Mike wrote.
http://www.binderplanet.com/forums/showwiki.php?title=Electrolytic+Rust+Removal
Forum: General FSJ Tech 09-28-2009, 04:18 PM
Replies: 11
Views: 3,319
Posted By SCscoutguy
I always take oven cleaner and my air compressor...

I always take oven cleaner and my air compressor and clean out the intake really well before I paint it and install it. You are right if you do not clean out the shot that is in the runners it can...
Forum: General FSJ Tech 09-28-2009, 01:54 PM
Replies: 11
Views: 3,319
Posted By SCscoutguy
I do the same exact thing. I take mine to the...

I do the same exact thing. I take mine to the NAPA machine shop and pay them $20 to blast it for me. Here is the intake off of my IH 392 before and after....
Forum: General FSJ Tech 09-26-2009, 11:07 AM
Replies: 8
Views: 1,883
Posted By SCscoutguy
I am not aware of any FSJ's coming with...

I am not aware of any FSJ's coming with Quadrajets. Some came with Motorcraft 4350's that had a proprietary spreadbore pattern. You will have to use a adapter in order to runn a quadrajet on that...
Forum: General FSJ Tech 09-20-2009, 12:02 PM
Replies: 5
Views: 689
Posted By SCscoutguy
I am about to do the same swap. From everything I...

I am about to do the same swap. From everything I have read it looks like the OBDII system in the 98 is going to be a bit more of a pain to swap than the older OBDI system. :( I totaled my 98...
Forum: General FSJ Tech 09-18-2009, 09:07 PM
Replies: 8
Views: 3,672
Posted By SCscoutguy
If your carter carburetor does have a electric...

If your carter carburetor does have a electric choke cap on it then you can swap it over to a MC 2100 but I believe you have to reverse the spring inside of it because the carter spring goes the...
Forum: General FSJ Tech 09-04-2009, 08:00 PM
Replies: 23
Views: 2,288
Posted By SCscoutguy
That is the exact one I have and it works fine...

That is the exact one I have and it works fine for tuning the engine.
Forum: General FSJ Discussion 08-20-2009, 10:50 PM
Replies: 19
Views: 782
Posted By SCscoutguy
Man I am shocked at some of these prices. Around...

Man I am shocked at some of these prices. Around here you can get a bench rebuild on your 727 for about $200-$250. I always just buy a kit on ebay and rebuild it myself. If you can follow simple...
Showing results 1 to 25 of 270
Page 1 of 11 1 23 > Last »

 
Forum Jump

All times are GMT -6. The time now is 02:38 AM.

Contact Us - International Full Size Jeep Association - Archive - Top

Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
corner IFSJA.org hosting provided by Golden Computer Service.
© 2000-2006 IFSJA Site Staff.   Jeep® is a registerd trademark of DaimlerChrysler. 		corner