International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: bufurd
Forum: General FSJ Discussion 11-17-2019, 01:39 PM
Replies: 3,500
Views: 259,361
Posted By bufurd
Continue to fight the battle... 3 cans of Fluid...

Continue to fight the battle... 3 cans of Fluid Film spraying every nook and cranny underneath,, my way of winterizing. :drivin:
Forum: General FSJ Tech 11-04-2019, 09:37 PM
Replies: 19
Views: 546
Posted By bufurd
An old points distributer with Petronix...

An old points distributer with Petronix conversion. Cheap and reliable.:drivin:
Forum: General FSJ Tech 11-04-2019, 09:21 PM
Replies: 6
Views: 261
Posted By bufurd
The loop side of a strip of self adhesive hook...

The loop side of a strip of self adhesive hook and loop fastener pressed in after cleaning out the old works good. :drivin:
Forum: General FSJ Tech 10-25-2019, 12:15 PM
Replies: 20
Views: 1,816
Posted By bufurd
Looks good, and a good looking rig. Now that the...

Looks good, and a good looking rig. Now that the springs are working right (cozy with each other the full length) something to help them slid against each other vastly improves ride quality. I spray...
Forum: General Chit-Chat 08-11-2019, 07:10 PM
Replies: 21
Views: 1,096
Posted By bufurd
I've a 74 J20 that I've put 176,000 on in the...

I've a 74 J20 that I've put 176,000 on in the last 4 years, put together right any of em will do it. My 70 I put about 35,000 a year on until the 74 got done.... The drums are fine if done up right,...
Forum: General FSJ Tech 08-07-2019, 02:29 PM
Replies: 18
Views: 517
Posted By bufurd
My opinion that pic is not how I would mount it,...

My opinion that pic is not how I would mount it, like said earlier, vertical (back a little bit okay) with the vehicle weight on it is how I'd roll. What you don't want is with the weight off (axle...
Forum: General FSJ Discussion 07-12-2019, 04:07 PM
Replies: 10
Views: 393
Posted By bufurd
Please don't throw nothing away there, was the...

Please don't throw nothing away there, was the outer spindle nut round with set screws to lock into the washer behind it? I LOVE the Lock-O-Matic hubs, keep in mind they won't work without the round...
Forum: General FSJ Discussion 06-16-2019, 07:06 PM
Replies: 4
Views: 386
Posted By bufurd
Was hoping when I seen the thread that there was...

Was hoping when I seen the thread that there was something done already, I love them things. Crawled under a few trucks with them to see how they mounted, doable, but I don't want to mount them to...
Forum: General FSJ Tech 05-14-2019, 08:32 PM
Replies: 10
Views: 590
Posted By bufurd
My take is that basing your timing on the base...

My take is that basing your timing on the base timing is starting on the wrong end. More important that the total timing and curve is right, the base timing ends up where it ends up as long it starts...
Forum: General FSJ Tech 05-11-2019, 10:28 PM
Replies: 8
Views: 618
Posted By bufurd
Wheel speed vibration, or driveline speed...

Wheel speed vibration, or driveline speed vibration? Pretty plain the difference. I would put it up on jack stands and see if it can be duplicated, finding out if it's front or rear shouldn't be too...
Forum: General FSJ Discussion 12-19-2018, 09:47 PM
Replies: 75
Views: 10,768
Posted By bufurd
Dang we move at our own speed, 2 years to reply...

Dang we move at our own speed, 2 years to reply and it don't seem too ridiculous. Anyway I hope them wickedly cool Jeeps of yours are getting some miles on em. I really don't know how to sum up the...
Forum: General FSJ Tech 12-08-2018, 04:54 PM
Replies: 7
Views: 393
Posted By bufurd
We are all a little different than most... I...

We are all a little different than most... I wouldn't mess with both of em, if ya want a 258 in the wag put one in it. Then you'll have 2 reliable Jeeps, according to some that's remarkable. :drivin:
Forum: Diesel Swaps 10-14-2018, 07:49 PM
Replies: 127
Views: 33,825
Posted By bufurd
Just turned over 163,000 miles, changed the last...

Just turned over 163,000 miles, changed the last wheel bearings (left rear) today. Not bad considering the axles now have over 200,000 on em, also ordered a replacement Bestop drivers bucket....
Forum: General FSJ Tech 09-20-2018, 08:35 PM
Replies: 18
Views: 2,648
Posted By bufurd
Yeah but it's a useful one. It inspired me to...

Yeah but it's a useful one. It inspired me to finally do mine, 74 J20, 215,000 miles on box. It wasn't bad but it had lost it's feel, I marked bearing adjustment before adjusting, it ended up about...
Forum: General FSJ Tech 04-28-2018, 10:30 PM
Replies: 9
Views: 904
Posted By bufurd
Pull the 4 little bolts on top, pull the cover...

Pull the 4 little bolts on top, pull the cover and take a shim or two out that'll tighten it up. :drivin:
Forum: General FSJ Tech 03-03-2018, 03:06 AM
Replies: 26
Views: 1,792
Posted By bufurd
The over center drag adjustment on box probably...

The over center drag adjustment on box probably could use a bit of snugging too, but extreme caution there. Your talking about maybe a 1/16th of a turn, 1/8th if bad, unlikely. :drivin:
Forum: General FSJ Tech 03-03-2018, 03:00 AM
Replies: 26
Views: 1,792
Posted By bufurd
On the back of the pump where the pressure line...

On the back of the pump where the pressure line connects if you pull the line off then put a big wrench on it and pull off the flow control valve in your hand will be what controls what you're...
Forum: General FSJ Discussion 01-18-2018, 07:45 PM
Replies: 4
Views: 795
Posted By bufurd
Yeah I struggle with computer things..... I wish...

Yeah I struggle with computer things..... I wish I'd a run into em to at least let em know its a J20. Thanks:thumbsup:
Forum: General FSJ Discussion 01-13-2018, 05:19 PM
Replies: 4
Views: 795
Posted By bufurd
Lot shot of the week

Don't know if this will work, but it's kinda cool.

www.onallcylinders.com/2018/01/03/lot-shots-find-of-the-week-j10-pickup-truck

Edit... Nope it didn't......
Forum: General FSJ Tech 01-08-2018, 09:50 PM
Replies: 7
Views: 577
Posted By bufurd
I don't trust em at all, 3 of mine release on...

I don't trust em at all, 3 of mine release on their own. The only one I trust is in Humpty, I replaced the peddle and all with an electric actuator mounted to the cross member. :drivin:
Forum: General FSJ Discussion 12-28-2017, 07:40 PM
Replies: 15
Views: 1,406
Posted By bufurd
If ya need a flywheel let me know, I have a B350...

If ya need a flywheel let me know, I have a B350 out of a 70 J truck in shop with the flywheel still on it.:drivin:
Forum: General FSJ Tech 12-13-2017, 09:08 PM
Replies: 4
Views: 851
Posted By bufurd
Any 70s GM car or truck will work and plug right...

Any 70s GM car or truck will work and plug right in, not sure how far before or after the 70s era will work but I'm sure some.:drivin:
Forum: General Chit-Chat 11-30-2017, 09:41 PM
Replies: 11
Views: 885
Posted By bufurd
If it's 2 12 volt batteries, very simple. You...

If it's 2 12 volt batteries, very simple. You hook your cables up just like you would jumping a "car", positive to positive, negative to negative to charge one battery at a time. If you have 2 cars...
Forum: General FSJ Tech 11-30-2017, 09:21 PM
Replies: 11
Views: 746
Posted By bufurd
Correct when the points are new, but they...

Correct when the points are new, but they (points) go down hill from there without maintenance. That's the advantage, the conversion is install and forget about it. Not picking on points, they are...
Forum: General FSJ Tech 11-29-2017, 09:59 PM
Replies: 11
Views: 746
Posted By bufurd
I've also got 3 vehicals running Pertronix...

I've also got 3 vehicals running Pertronix ignition, no issues. If you're worried, put the points unit in the Pertronix box and throw it in the glove box. Keeping that high quality distributor you...
Showing results 1 to 25 of 500

 
Forum Jump

All times are GMT -6. The time now is 03:05 AM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
corner corner