International Full Size Jeep Association
Home Forums Reader's Rigs Tech Library Trail Stories FSJ-List
International Full Size Jeep Association  

Go Back   International Full Size Jeep Association > Search Forums

Showing results 1 to 25 of 49
Search took 0.01 seconds.
Search: Posts Made By: pickledtoast
Forum: Fuel Injection 10-14-2021, 12:30 PM
Replies: 4
Views: 3,227
Posted By pickledtoast
The initial 15 was updated to 22 to get more...

The initial 15 was updated to 22 to get more vacuum at idle. I'd post a screenshot but that's difficult on this site.

The current ignition map, following the above video, has ignition timing at...
Forum: Fuel Injection 10-06-2021, 12:42 PM
Replies: 4
Views: 3,227
Posted By pickledtoast
Touchpad wizard I initially went with 15 idle, 36...

Touchpad wizard I initially went with 15 idle, 36 cruise, 32 WOT. But the wizard created timing map is scary. It looks like this with your three entered...
Forum: Street & Performance 09-22-2021, 07:19 AM
Replies: 79
Views: 69,783
Posted By pickledtoast
I'm at $50 for the LS rockers off ebay, $15 for...

I'm at $50 for the LS rockers off ebay, $15 for the raw material from McMaster. Hardware is borrowed from work. Lunch hours machining instead of playing on the internet: "free".

Anyway, seat of the...
Forum: Street & Performance 05-03-2021, 11:45 AM
Replies: 79
Views: 69,783
Posted By pickledtoast
Yes I made new stands as the LS stand shaft...

Yes I made new stands as the LS stand shaft height is too high. .200" removed from the LS shaft height; unfortunately there's not enough there on the LS stand to take that much off. I used mild steel...
Forum: General FSJ Tech 04-21-2021, 02:11 PM
Replies: 268
Views: 618,716
Posted By pickledtoast
As possibly seen above with 31x10.5 on 15x8,...

As possibly seen above with 31x10.5 on 15x8, skyjacker 4":
https://live.staticflickr.com/65535/51130172288_e35be04324_c.jpg

With 32x11.5 on...
Forum: Street & Performance 04-21-2021, 12:13 PM
Replies: 79
Views: 69,783
Posted By pickledtoast
Here I am still attempting to find a place to...

Here I am still attempting to find a place to host images for forums. Lets try...
Forum: Fuel Injection 06-10-2020, 05:52 PM
Replies: 5
Views: 5,277
Posted By pickledtoast
Nice job getting that holley fuel pump assembly...

Nice job getting that holley fuel pump assembly grafted to the oem tank. I didn't think that was possible.

I spend days getting the OEM fuel sender/pickup modified to accept the fuel pump. I think...
Forum: Street & Performance 05-18-2020, 11:22 AM
Replies: 79
Views: 69,783
Posted By pickledtoast
Test here for uploading...

Test here for uploading...
Forum: Street & Performance 05-18-2020, 10:41 AM
Replies: 79
Views: 69,783
Posted By pickledtoast
Yeah, please do a back to back test on the dyno...

Yeah, please do a back to back test on the dyno if you could. I hoped to do that but am getting grief here at work putting my AMC on the dyno, as we don't have the AMC adapters for the dyno.

If I...
Forum: General FSJ Tech 05-11-2020, 12:14 PM
Replies: 12
Views: 1,181
Posted By pickledtoast
Yep, that left one is on it's way out. Time to...

Yep, that left one is on it's way out. Time to change the cam and lifters. Relatively cheap fix. Be sure to use oil with zinc in it, or buy a zinc additive.
Forum: General Chit-Chat 01-14-2020, 01:00 PM
Replies: 25
Views: 5,328
Posted By pickledtoast
I do not see pics.

I do not see pics.
Forum: General FSJ Tech 01-09-2020, 10:18 AM
Replies: 97
Views: 58,474
Posted By pickledtoast
Thanks for the TPS values. I have yet to measure...

Thanks for the TPS values. I have yet to measure mine, but wasn't sure if your later AW4 tps had inverted values or not. Good to know it doesn't and that I can likely just tap the Sniper tps on mine....
Forum: General FSJ Tech 01-06-2020, 01:07 PM
Replies: 97
Views: 58,474
Posted By pickledtoast
From your testing, what were your...

From your testing, what were your voltage/throttle percent values for TPS?
Forum: General FSJ Tech 01-06-2020, 11:32 AM
Replies: 97
Views: 58,474
Posted By pickledtoast
I'm running a '97 TCU in a <96 trans (with...

I'm running a '97 TCU in a <96 trans (with newer 97+ NSS swapped in, but still running the old reed style single VSS). The '97 brake sense gets switched to ground, open when brake pedal pushed. if...
Forum: General FSJ Tech 01-06-2020, 10:47 AM
Replies: 97
Views: 58,474
Posted By pickledtoast
.280" spacers by my earlier measurements....

.280" spacers by my earlier measurements.

keep up the excellent updates!
Forum: General FSJ Discussion 12-30-2019, 01:06 PM
Replies: 30
Views: 4,036
Posted By pickledtoast
Nice, pretty slick install there. So a...

Nice, pretty slick install there. So a rectangular hole needs to be cut into the inner rocker panel to insert the 'j clips'. Seems simple enough.
Forum: General FSJ Tech 12-03-2019, 06:57 AM
Replies: 97
Views: 58,474
Posted By pickledtoast
Yeah you're right. I just rough tape measured my...

Yeah you're right. I just rough tape measured my A727 at around 23", so that 22.625 value is probably right. I don't know what kinda crack I was smoking before.
Forum: General FSJ Tech 12-02-2019, 08:53 AM
Replies: 97
Views: 58,474
Posted By pickledtoast
I was getting almost the same, until you pointed...

I was getting almost the same, until you pointed out we need the 7/8 spacer to reuse the NP229. So now I have 7/8" further rearward.

That's me measuring bellhousing to transfer case flange with a...
Forum: General FSJ Tech 12-02-2019, 07:48 AM
Replies: 97
Views: 58,474
Posted By pickledtoast
4" eh. I'm getting no where near that with...

4" eh. I'm getting no where near that with my tape measure, but you are further along than I am.
Forum: General FSJ Tech 12-02-2019, 07:45 AM
Replies: 7
Views: 1,104
Posted By pickledtoast
Man I have to get on this. Not too many pick n...

Man I have to get on this. Not too many pick n pulls by me though.
Forum: General FSJ Tech 11-19-2019, 11:40 AM
Replies: 21
Views: 5,626
Posted By pickledtoast
I got this stalk from Amazon. Quality is ok, good...

I got this stalk from Amazon. Quality is ok, good for the price. $21

https://www.amazon.com/gp/product/B007TY2PNA/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

Brain I got off one of the facebook...
Forum: General FSJ Tech 10-29-2019, 08:01 AM
Replies: 97
Views: 58,474
Posted By pickledtoast
Similar reasons here for keeping the NP229. My...

Similar reasons here for keeping the NP229. My vacuum shifter works well for now.

But...the vehicle speed signal for the TCU comes from the 242 VSS. I'm not sure yet how I will handle that....
Forum: General FSJ Tech 10-17-2019, 12:38 PM
Replies: 97
Views: 58,474
Posted By pickledtoast
I'm not entirely confident in my initial waggy...

I'm not entirely confident in my initial waggy flexplate digitization. I will redo it when it all comes apart and remeasure. That said, I have about .175" difference between my '90 wagoneer flexplate...
Forum: General FSJ Tech 10-15-2019, 07:50 AM
Replies: 97
Views: 58,474
Posted By pickledtoast
Yeah, makes sense. Should be a simple job for...

Yeah, makes sense. Should be a simple job for those equipped and a smart solution overall.
Forum: General FSJ Tech 10-15-2019, 07:42 AM
Replies: 97
Views: 58,474
Posted By pickledtoast
I guess you would need the crank/damper to...

I guess you would need the crank/damper to balance the flexplate, as the 360 flexplate is not zero balance. Or you can probably eyeball the 360 flexplate weight and holes and copy them on the AW4...
Showing results 1 to 25 of 49

 
Forum Jump

All times are GMT -6. The time now is 07:17 PM.


Powered by vBulletin Version 3.5.4
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
corner corner