PDA

View Full Version : parts swap?


Blake
10-18-2012, 11:37 PM
I have a stock 4 barrel intake manifold for an AMC V8 that Tad has dibs on.

I also have a pair of AMC V8 exhaust manifolds including good air tubes (bolts are free and not frozen up).

Other parts such as flex plates, emissions components, etc, etc, etc.

Anyone interested?

fulsizjeep
10-19-2012, 05:22 PM
We have FSJ stuff too. More than I care to list but if you are hunting for something, post up - someone else in the group may just have it. I do have abundance of 360/T400 flex plates, otherwise we have stuff that fits bumper to bumper.

the original Honcho
10-19-2012, 10:06 PM
I could use a front drivers side sidemarker light and bezel for a '75 wagoneer and a front passengerside sidemarker light for a '91 Grand wagoneer. Any or both at a reasonable price would be great :thumbsup:

Tad
10-20-2012, 06:38 AM
I'll have to let someone else go for the intake.
Buddy has been unemployed for a few weeks, no spare cash and he's most likely heading out of state for a bit.

Heimeken
10-20-2012, 11:16 AM
Stuff I am looking for:
Working 727 Transmission
33" Tires and rims, 8 lug 16" or 17" rim diam.
Shocks for 2 or 3 inch lifted FSJ in good shape
CV driveshaft with 2" tube diameter any length
Heater housing in good shape
Radio antenna (just the whip) for 79

Stuff in my junk pile for sale:
Front wide-track bumper (the lightweight one)
360 Flywheel
A Couple of 401 flex plates
power steering pumps
Engine/transmission mid plate
sway bar
4" lift springs for rear axle (like new)
air cleaner housing
dana 44 spindles with surface rust
universal winch mount/plate
Various D44 and D60 Yokes (strap style)
Shackles, both stock and M715 style
Dana 60 rear axle for 79 and older (needs complete rebuild)
Dana 70HD axle from chevy(4.11, open,ready to run)

Blake
10-20-2012, 01:25 PM
I have 3 or 4 front 1310 cv shafts for an fsj.

What specifically are you looking for?

Heimeken
10-20-2012, 02:38 PM
FJS shafts cannot really be sleeved like the 2" ones can with a stock pipe to make as a backup that is why I am specifically looking for a 2" diameter shaft, CV with 1310 joints. I have plenty of FSJ front shafts also:cool:


I have 3 or 4 front 1310 cv shafts for an fsj.

What specifically are you looking for?

mcjeep80
10-20-2012, 08:41 PM
i have a few good heater housings. metal and fiberglass. which one you want? i also have the 727 that was in my jeep. it has been outside for the last 2 months. it was a fresh rebuild with a few goodies. b&m rebuild kit and transgo rv shift kit, bolt in sprag, 4 gear planetary set and a deep steel pan. $500 obo comes with a high stall converter and a lokar cable.

Heimeken
10-20-2012, 09:34 PM
mmm, wasn't planning on spending that much on a tranny... but let me think about it as this one seems well built. Is it the original 23 spline output?

As for the heater housing, pm me what you want for whatever is in the best condition.

i have a few good heater housings.....

Michael
10-21-2012, 12:53 AM
Jaime, what do u want for the 4" rear springs?

Blake
10-21-2012, 01:48 AM
i have a few good heater housings. metal and fiberglass. which one you want? .

how much for a good metal heater housing? I busted the fiberglass one on the waggy when installing the 401.

Michael
10-21-2012, 06:33 AM
Is that Dana 60 offset Jaime?

mcjeep80
10-21-2012, 06:39 AM
how about $20 for a heater housing. i have 2 metal ones and 2 good fiberglass ones. as for the tranny, make me an offer it is just siting there.

Blake
10-21-2012, 10:24 AM
how about $20 for a heater housing. i have 2 metal ones and 2 good fiberglass ones. as for the tranny, make me an offer it is just siting there.

I'll take a metal one. thanks! :thumbsup: