Front Axle Shafts from BJ's Off-Road!

[TPICherokee]

We now have chromoly axle shafts made by Dutchman!

Inner Shafts:

http://www.bjsoffroad.com/CartGenie/prod-1022.htm

http://www.bjsoffroad.com/cartgenie/images/large/inner_shaft.jpg


Outer Shafts:

http://www.bjsoffroad.com/CartGenie/prod-1023.htm

http://www.bjsoffroad.com/cartgenie/images/large/outer_shaft.jpg

All made in the USA, all custom built! We have 99% of all measurements so you just need to tell us your vehicle and we would have your axles in stock in about a week!

These ended up being cheaper than the old Warn shafts AND we can get them in widetrack lengths!

Thanks!

[thomastenn]

can they do the 33 spline for the detroits?

[TPICherokee]

I am 99% sure they can, there may be an extra cost. I will call them on Monday and find out.

[fulsizjeep]

:thumbsup:
I like it! Any chance we could get rear axles too? :fsj:

[thomastenn]

im thinking make a super waggy 44 kit with the 33 spline choice or lockers and blow superiors axle kits out of the water lol

[TPICherokee]

:thumbsup:
I like it! Any chance we could get rear axles too? :fsj:

Yes, we can. We have the Grand Wagoneer ones listed online now but I was going to wait until I had them all listed (of course the QT rigs will be more expensive since they are over a certain length) and needed to figure it out first...

[TPICherokee]

im thinking make a super waggy 44 kit with the 33 spline choice or lockers and blow superiors axle kits out of the water lol

Not a bad idea, I'll let you know.

[fulsizjeep]

Yes, we can. We have the Grand Wagoneer ones listed online now but I was going to wait until I had them all listed (of course the QT rigs will be more expensive since they are over a certain length) and needed to figure it out first...My first interest would be for a 77 J10 axle. Pretty sure it had a QT. I have not had the shafts out yet.

[TPICherokee]

My first interest would be for a 77 J10 axle. Pretty sure it had a QT. I have not had the shafts out yet.

Flint, if you get me the BOM off of the axle, I can tell you what it came out of and get you a quote for some Chromoly shafts. Thanks!

[fulsizjeep]

I guess I am not sure where the BOM info is on the axle. I read it was on the long side on the tube. I don't see any markings on either tube. The carrier is offset slightly to the right. Not as far as a QT NT axle though. I got numbers off the flanges of each axle shaft. Is that it?

[TPICherokee]

Sometimes the numbers are really hard to read but I have yet to find an axle that didn't have them:

http://www.bjsoffroad.com/jeeps/bom.jpg

[fulsizjeep]

thank you Brent! :thumbsup:

this one has it on the short side (right hand side)

9 11 8A3
603941 1

this is going in Wally (88 GW) when we go SOA &
SF will be 4.10 gears and a Lockright with 35s
would like some strong shafts for it :cool:

[novacayne75]

wow. is $195 per shaft or set. and how is the warranty? ill be getting a couple sets of these!

[TPICherokee]

thank you Brent! :thumbsup:

this one has it on the short side (right hand side)

9 11 8A3
603941 1

this is going in Wally (88 GW) when we go SOA &
SF will be 4.10 gears and a Lockright with 35s
would like some strong shafts for it :cool:

Huh, I just learned something. First the easy stuff. It is out of a 1979 J-truck with 3.54 gears.

What I learned was that the J-trucks ran the same axle whether it was a QT or not. I didn't realize this.

In the spicer books, it says, Cherokee Chief Std Transfer Case has one Dana 44 in it and then it says Cherokee Chief Quadratrac Transfer Case which shows a different Dana 44, and repeats for the Wagoneers, but doesn't say this for the J-trucks, only shows one axle width per year for the J-trucks irregardless of whether they had a QT or not...

I'll let you know a price tomorrow.

[TPICherokee]

wow. is $195 per shaft or set. and how is the warranty? ill be getting a couple sets of these!

I'll double check on the warranty when I call about Flint's shafts. $195 is per axle on the front inner shafts. It is actually cheaper with the IFSJA discount but not the full 15%.

[fulsizjeep]

Huh, I just learned something. First the easy stuff. It is out of a 1979 J-truck with 3.54 gears.

What I learned was that the J-trucks ran the same axle whether it was a QT or not. I didn't realize this.

In the spicer books, it says, Cherokee Chief Std Transfer Case has one Dana 44 in it and then it says Cherokee Chief Quadratrac Transfer Case which shows a different Dana 44, and repeats for the Wagoneers, but doesn't say this for the J-trucks, only shows one axle width per year for the J-trucks irregardless of whether they had a QT or not...

I'll let you know a price tomorrow.So the date is 9/11/78 on the manufacture? Thanks for the info. Interesting the axles are the same for D20 and QT J10s.

[TPICherokee]

So the date is 9/11/78 on the manufacture? Thanks for the info. Interesting the axles are the same for D20 and QT J10s.

I can't find any way to decode the date code but I think you are probably correct.

Price on the rear axles IFSJA is $270. Since all of the QT rigs (including Wag, Chief and J-truck) have a longer than normal axle, there is a $60 up charge for these axles rigs.

Total price on a set of rear shafts for a quadratrac rig is $330 IFSJA price. If you want bearings and retainers installed to the shafts, the price is $95 extra for that.

I'll get these up on the webstore tonight or tomorrow.

Thanks!

[TPICherokee]

Flint, 1974-1979 Rear Axle Shafts are here:

http://www.bjsoffroad.com/CartGenie/prod-1038.htm

Thanks!

[TPICherokee]

wow. is $195 per shaft or set. and how is the warranty? ill be getting a couple sets of these!

They don't give a manufacturers warranty for anything 30 spline and under. We offer a 12 month warranty on everything we sell so we would honor this warranty. We won't warranty the ears that the u-joints attach to or abuse.

[TPICherokee]

im thinking make a super waggy 44 kit with the 33 spline choice or lockers and blow superiors axle kits out of the water lol

We can upgrade the axles to 33 spline for no extra charge. With 33-spline axles, the manufacturer warranties the spline end of the shaft for 2 years!

[novacayne75]

I'll double check on the warranty when I call about Flint's shafts. $195 is per axle on the front inner shafts. It is actually cheaper with the IFSJA discount but not the full 15%.
i thought that was to good of a deal. ill stick to the tenfactory shafts

[fulsizjeep]

Flint, 1974-1979 Rear Axle Shafts are here:

http://www.bjsoffroad.com/CartGenie/prod-1038.htm

Thanks!Thanks for the footwork Brent. Now I need to talk with Mrs. Claus ;)

[jeepdreamer]

Sorry... pet peeve. "Irregardless" is not a word! Its just regardless. haha. Kinda like saying "reverse discrimination".. no such animal. Great deal on the axles though!! Come on money.....